Arrow Storage Products CG1012 Owner'S Manual & Assembly Instructions Download Page 30

Page: 30 / 36

Step 17

SQ30

Parts Needed For

Roof Assembly

6529 Roof Panel (2)

6641 Left Roof Panel (1)

6869 Ridge Cap (1)

6640 Right Roof Panel (1)

Install two roof panels, left roof

panel, ridge cap 6869 and right

roof panel on the front of the roof

as before.

Fasten the roof panel ribs, peak

cap and ridge cap together using

bolts and nuts.

Fasten the lower end of the panels

to the side wall angles using screws

and washers.

Peak Cap

STEP

6529

STEP

Cut

Weather Stripping

and Fold Under

6641

6529

6640

6869

Attach the side roof trim pieces

to the lower end of the roof panels

on each side of the building using

screws at each panel overlap.

NOTE

A single screw fastens both trim

pieces at the overlap.

Using your thumb and index fi nger,

overbend the bottom fl ange of the side

roof trim at the corner inward enough

so the right and left roof trim caps fi t

onto right and left corners.

Fasten the roof trim caps to the

side trim using a screw.

6015 Side Roof Trim (4)

6014 Side Roof Trim (2)

Parts Needed For

Roof Trim

Step 18

SQ31

Tuck Flange

Inward to Fit

Inside of

Roof Trim Cap

STEP

Roof Trim Cap

STEP

6014

6015

Roof Trim

6014

6015

Summary of Contents for CG1012





































Search results

Summary of Contents for CG1012

Reviews:

Related manuals for CG1012

Brands by name

Popular brands

Arrow Storage Products CG1012, Owner'S Manual & Assembly Instructions

Search results

Summary of Contents for CG1012

Reviews:

Related manuals for CG1012

Brands by name

Popular brands