Arrow Storage Products CG1012 Owner'S Manual & Assembly Instructions Download Page 28

Page: 28 / 36

Step 15

SQ28

6641 Left Roof Panel (1)

6529 Roof Panel (2)

6869 Ridge Cap (1)

Parts Needed For

Roof Assembly

Install a left roof panel at the left

rear corner of the roof.

Install two roof panels in the

sequence shown on previous page.

Follow fastener sequence while fas-

tening roof panels.

NOTE

Narrow roof panel rib (with bead

on it) is always overlapped by

wide rib of adjacent panel

Cover the joint at the peak with

weather stripping tape. Unroll the

tape and press it down over the open-

ing at the ridge as you install each

roof panel. Do not cut the tape until

entire roof is completed.

Install one ridge cap 6869 on the

roof section using bolts and nuts.

Fasten the roof panel ribs, peak

cap and ridge cap together using

bolts and nuts.

Screws To

Roof Beam

Fasten at

Overlap With

Bolt

Screws To

Roof Beam

Do not fasten

at this time

Weather

Stripping

Tape

STEP

6529

Roof Panel

STEP

6529

6869

6641 Left Roof Panel

Fasten at

Overlap With

Bolt

Summary of Contents for CG1012





































Search results

Summary of Contents for CG1012

Reviews:

Related manuals for CG1012

Brands by name

Popular brands

Arrow Storage Products CG1012, Owner'S Manual & Assembly Instructions

Search results

Summary of Contents for CG1012

Reviews:

Related manuals for CG1012

Brands by name

Popular brands