manualshive.com logo in svg

Arris BGW210-700, Install And Operation Instructions

Share
Download
Arris BGW210-700 Install And Operation Instructions Download Page 9

Chapter 3: Hardware Gateway Installation 

 

365-095-30882 Revision 4.0 

BGW210-700 Broadband Gateway Release 1.0 Install and Operations Guide 

© 2016 ARRIS Enterprises LLC. All Rights Reserved. 

9 

 

 

Chapter 3 

Hardware Gateway Installation 

A BGW210-700 Broadband Gateway cabling overview, as well as rear panel illustration, is 
provided below. Also provided are procedures to perform BGW210-700 Broadband Gateway 
connections for the power adapter, wired Ethernet, wireless devices, Internet, and VoIP 
telephones. 

The following diagram illustrates BGW210-700 Broadband Gateway connections to the 
Internet using DSL Broadband. Phone and power adapter connections are also illustrated. 

BGW210-700 Broadband Gateway Cabling Overview 

 

Alternatively, you can connect the BGW210-700 Broadband Gateway to the Internet using the 
WAN Ethernet port labeled ONT. See 

Connecting the BGW210-700 Broadband Gateway to the 

Internet

 (page 13) for the detailed procedures regarding this setup. 

Summary of Contents for BGW210-700

































Reviews:

No comments

Brands by name

Popular brands

Load more brands