manualshive.com logo in svg

Arris BGW210-700, Install And Operation Instructions

Share
Download
Arris BGW210-700 Install And Operation Instructions Download Page 30

Chapter 6: Important Safety Instructions 

 

365-095-30882 Revision 4.0 

BGW210-700 Broadband Gateway Release 1.0 Install and Operations Guide 

© 2016 ARRIS Enterprises LLC. All Rights Reserved. 

30 

 

Service Requirements 

In the event of equipment malfunction, if under warranty, we will exchange a product 
deemed defective. Under FCC rules, no customer is authorized to repair this equipment. This 
restriction applies regardless of whether the equipment is in or out of warranty. 

Technical Support for Hardware Products: 
Customers inside North America: 888-944-4357 (888-944-HELP) 
Customers outside North America: 1-215-323-2345 
For Spanish language support: 1-215-323-2346 

  Note: This product was tested for FCC compliance under conditions that included the use of 

shielded cables and connectors between system components. Changes or modifications to 
this product not authorized by the manufacturer could void your authority to operate the 
equipment. 

 

 

 

Summary of Contents for BGW210-700

































Reviews:

No comments

Brands by name

Popular brands

Load more brands