manualshive.com logo in svg

ARMTEL ARMT.665200.003UM, User Manual

Share
Download
ARMTEL ARMT.665200.003UM User Manual Download Page 3

DCN-2 CENTRAL EXCHANGE 

User Manual 

armtel.com

 

 

page

 1/44  

[email protected] 

 

© Armtel

 

ENG 

INTRODUCTION 

This  User  Manual  is  intended  for  introducing  «DCN-2  Central  Exchange» 

ARMT.665200.003 manufactured by Armtel LLC, Russia and it is intended to familiarize the 
user with the switch device and the procedure for its operation at the installation site. 

The  DCN-2  Central  Exchange  is  a  compact  switching  node  of  the  digital  system  of 

operational and technological communication and loud notification DCN. 

Short name of the product – DCN-2. 

Maintenance  personnel  for  DCN-2  shall  be  appointed  by  the  management  at  the 

installation  site.  The  maintenance  personnel  shall  be  required  to  know  the  operating 
procedure of DCN-2 to the extent provided for by the User Manual. 

Duties of the maintenance personnel shall include maintenance of DCN-2 by this User 

Manual. 

 

 

 

 

Summary of Contents for ARMT.665200.003UM

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands