manualshive.com logo in svg

Armitage Shanks Sensorflow 21 A4845AA, Installation Instructions Manual

Share
Download
Armitage Shanks Sensorflow 21 A4845AA Installation Instructions Manual Download Page 14

14

INSTALLATION GUIDE continued…

Electrical connection continued…

Sensor taps stickers:

 To complete the installation, 2 stickers are 

provided which can be stuck onto a wall or panel in close proximity to 

this product to advise the end user that this product sensor operated.

6 

TAP OPERATION

Sensorflow 21 products use an Infrared Sensor to activate the system.

The sensor is triggered by something reflective (normally hand movement) in the Sens

-

ing Region.

Move hands towards the spout: Water 

will flow.

    

Move hands away from the  

spout:  Water will continue 

to flow for a second or 

two, and then turn off.

   

Sensor is factory set to 

Proximity Mode

, & is 

designed to trigger the water flow 

only when a hand (or similar) is in 

the Sensing Region –

 just in front 

of the sensor / outlet.  

   

For this range of products, the sensor 

is located near the flow outlet and faces 

downwards, towards the basin.

Example above of an installation where PSUs are all mains versions.

100

Summary of Contents for Sensorflow 21 A4845AA





















Reviews:

No comments

Brands by name

Popular brands

Load more brands