ARM Cortex-R4 Technical Reference Manual Download

Page: 99 / 436

System Control

ARM DDI 0363G

4-29

ID073015

Non-Confidential

Table 4-15

shows the ID_ISAR1 bit assignments.

To access the ID_ISAR1 read CP15 with:

MRC p15, 0, <Rd>, c0, c2, 1 ; Read ID_ISAR1

c0, Instruction Set Attributes Register 2

The ID_ISAR2 is:
•

a read-only register

•

accessible in Privileged mode only.

The ID_ISAR2 characteristics are:

Purpose

The ID_ISAR2 provides information about the instruction set that the
processor supports beyond the basic set.

Table 4-15 ID_ISAR1 Register bit assignments

Bits Name

Function

[31:28]

Jazelle
instructions

Indicates support for Jazelle instructions:

0x1

= the processor supports:

•

BXJ

instruction

•

J bit in PSRs.

For more information see

Program status registers

on page 3-9

and

Acceleration of execution

environments

on page 3-25

[27:24]

Interworking
instructions

Indicates support for interworking instructions:

0x3

= the processor supports:

•

, and T bit in PSRs

•

BLX

, and PC loads have BX behavior

•

data-processing instructions in the ARM instruction set with the PC as the destination
and the S bit clear have BX-like behavior.

[23:20]

Immediate
instructions

Indicates support for immediate instructions:

0x1

= the processor supports:

•

the

MOVT

instruction

•

MOV

instruction encodings with 16-bit immediates

•

Thumb

ADD

and

SUB

instructions with 12-bit immediates.

[19:16]

ITE
instructions

Indicates support for If Then instructions:

0x1

= the processor supports

instructions.

[15:12]

Extend
instructions

Indicates support for sign or zero extend instructions:

0x2

= the processor supports:

•

SXTB

SXTB16

SXTH

UXTB

UXTB16

, and

UXTH

•

SXTAB

SXTAB16

SXTAH

UXTAB

UXTAB16

, and

UXTAH

[11:8]

Exception 2
instructions

Indicates support for exception 2 instructions:

0x1

= the processor supports

RFE

SRS

, and

CPS

[7:4]

Exception 1
instructions

Indicates support for exception 1 instructions:

0x1

= the processor supports

LDM

(exception return),

LDM

(user registers), and

STM

(user

registers).

[3:0]

Endian
instructions

Indicates support for endianness control instructions:

0x1

= the processor supports

SETEND

and E bit in PSRs.

Summary of Contents for Cortex-R4


















































































































































































































































































































































































































































Search results

Summary of Contents for Cortex-R4

Reviews:

Related manuals for Cortex-R4

Brands by name

Popular brands

ARM Cortex-R4, Technical Reference Manual

Search results

Summary of Contents for Cortex-R4

Reviews:

Related manuals for Cortex-R4

Brands by name

Popular brands