Installation
Before using the Bari-Breeze mattress replacement system, remove
any other mattress from the bed.
1. When installing the Bari-Breeze mattress, place the mattress
directly on the bed frame.
Make sure that the tubeset end of the mattress is at the
foot end of the bed.
2. There are sixteen nylon black straps with buckles on the base
of the mattress. Loop each strap around the bed frame and
fasten it securely to the bed frame using the buckle.
3. Open the hooks on the back of the pump and suspend the pump
from the bed foot rail. If the bed you are using does not have
a foot rail, place the pump upright on its base on a flat surface
underneath the bed near the foot of the bed frame.
Static Mode
Max Flow
Pressing the
Max Flow
button sets the pump to maximum
flow, fully inflating the mattress and overriding the comfort
control. This feature is only available in static mode.
If pressed during
Turn
mode, it will revert the system to
Static
mode and return the patient to a central position.
Max Flow
inflates the mattress to maximum pressure for
15 minutes. A blue indicator on the button will show when it
is active and an is shown in the LED display.
To cancel
Max Flow
and to enter
Turn
mode settings, press
the
Max Flow
button once. To continue
Max Flow
for
more than 15 minutes, press
once to cancel, and quickly
again to enter
Max Flow
for a further 15 minutes. After 15
minutes,
Max Flow
is automatically cancelled.
Turn Options
Uni-Lateral Turn
To enter uni-lateral mode, press the
button to cycle
through until or is selected. This is confirmed by the
illuminated blue indicator.
ArjoHuntleigh AB
Verkstadsvägen 5
241 38 Eslöv
SWEDEN
www.arjohuntleigh.com
® and ™ are trademarks of ArjoHuntleigh
As our policy is one of continuous improvement, we reserve the right to modify designs without prior notice.
647903EN_02: 10/2012
CPR Control
IN THE EVENT OF CARDIAC ARREST
To Activate the CPR
Located on the right hand side of the pump is a CPR
device marked with an arrow. In the event of cardiac
arrest, press the two quick release catches on the
tubeset/pump connector, and simultaneously pull the
hose away from the pump.
SAFETY SIDES
Regarding the use of safety sides, always refer to your local
trust policy AND the product instructions for use.
Note:
Note:
Attach the mattress to the movable parts of the bed
only.
4. Plug the mains power cord into the pump. Insert the mains
power plug into a suitable mains power socket.
5. Securely attach the pump connector onto the pump until it
clicks, and make sure the air plug for the side bolsters and
base air pad is secure.
6. If not already fitted, place the protective cover over the mattress
and secure in position. Make sure the
ArjoHuntleigh
logo is
uppermost and at the foot end of the mattress.
Cable Management
Make sure that the mains power cable is positioned to avoid causing
a trip or other hazard, and is clear of moving bed mechanisms or
other possible entrapment areas.
Initial Power Up
Press the power/standby button to turn the pump on. An audible beep
will sound. The system will go into a start up cycle for 30 seconds,
during which time the pump will rapidly inflate the mattress. During
this process the 7 segment display will alternate between ‘
b
‘ and
‘
f
‘ to indicate bolster fill.
Once the mattress is fully inflated and with the patient in position,
adjust the comfort controls to the desired level.
Adjust if necessary to make sure the patient does not sink through
to the base air pad.
Recommended Pressure Settings
For extra firm support during patient handling or nursing procedures,
it is recommended to set the mattress pressure to maximum by
pressing
Max Flow
.
When the backrest is raised and the patient is in a semi-recumbent
position, it is recommended to press the
Max Flow
button to
increase the pressure/comfort level accordingly to make sure the
patient does not bottom out.
Bi-Lateral Turn
To enter bi-lateral Turn mode, press the button until is
selected. This is confirmed by the illuminated blue indicator.
Turn Times
To set therapy turn times, press the
MIN
button until the
desired time is indicated, this is confirmed by the illuminated
blue LED.
To Reset the CPR
Reconnect the tubeset to the pump.
