manualshive.com logo in svg

ARJAY ENGINEERING 2880R-LT, User Manual, Page: 5 / 28

Share
Download
ARJAY ENGINEERING 2880R-LT User Manual Download Page 5

 

2880R-LT, 2881R-LT, 2882R-LT

 

Revision 1.0

 

P a g e  5 | 28

 

Specification 

Details 

Installation Category 

II 

Pollution Degree 

2 

Equipment mobility 

Fixed 

Mechanical Specification: 

Refer to Dimensional Drawing 

Protection Degree –  
Controller & Probe Junction 

Box

 

IP65 

2800 Series Controller And 
Remote Level Probe 
Certification 
(Hazardous Locations) 

 

North America 

•

  CSA file number: 56812 

•

  Class – 2258-02 – Process control equipment for Hazardous 

Locations 

•

  Class – 2258-82 – Process control equipment for Hazardous 

Locations – Certified to US Standards 

•

  Ex db IIC T5 Gb 

•

  Class I, Zone 1, AEx db IIC T5 Gb 

International IECEx/ATEX 

•

  II 2G Ex db IIC T5 Gb 

•

  Sira 17ATEX1303X 

•

  IECEx CSA 17.0034X 

 

SPECIFIC CONDITIONS OF USE FOR HAZARDOUS LOCATION  
(denoted by X after the certificate number) 
 
1.  Process temperature for the standard and heavy duty probes are -60°C to +200°C and for 

flexible probe is -60°C to +100°C. It is end-user’s responsibility to ensure that the ambient 
around the Capacitance Controller and ARJAY Probe does not exceed the permitted ambient of 
+55°C. 

 
2.  The maximum process pressure is 1500psi/ 10342KPa. 

 

3.  Only approved certified entry devices shall be used. 

 

4.  Flameproof joints are not permitted to be repaired in the field. If the flamepath is damaged, the 

enclosure is to be removed from service and replaced with a new enclosure. 

 

 

Summary of Contents for 2880R-LT





























Reviews:

No comments