ARJAY ENGINEERING 2880R-LT User Manual Download

Page: 3 / 28

2880R-LT, 2881R-LT, 2882R-LT

Revision 1.0

P a g e 3 | 28

TABLE OF CONTENT

NOTICE

Please

read the Installation Notes (4.0) prior to locating and mounting

the instrument.

1.0

SPECIFICATION .................................................................................................... 4

2.0

USE

HAZARD

INFORMATION ............................................................................... 7

3.0

INSTRUMENT

OVERVIEW ..................................................................................... 8

3.1

Features ............................................................................................................................... 9

3.2

Model Number Table ............................................................................................................ 9

4.0

INSTALLATION .................................................................................................... 10

4.1

Probe Mounted Controller Installation ................................................................................ 10

4.2

Probe Installation ................................................................................................................ 11

5.0

CONTROLLER

OVERVIEW ................................................................................. 13

5.1

Input / Output Terminal Specification ................................................................................. 14

5.2

Permanent Power Connection (AC Powered Models Only) ............................................... 15

5.3

Glossary Of Symbols .......................................................................................................... 15

6.0

STARTUP

AND

CALIBRATION ........................................................................... 16

6.1

Startup ................................................................................................................................ 16

6.2

Menu Flow Chart Back Chart Background Information ...................................................... 16

6.2.1

Menu Short Form ................................................................................................................ 16

6.2.2

Menu Description ................................................................................................................ 17

6.2.3

Data Entry ........................................................................................................................... 17

6.3

288XR Controller Setup ...................................................................................................... 17

6.3.1

Setup And Network ............................................................................................................. 17

6.3.2

Relay Setup Menu .............................................................................................................. 18

6.4

288XR Controller Calibration .............................................................................................. 20

6.4.1

Auto Calibration .................................................................................................................. 20

6.4.2

Manual Calibration .............................................................................................................. 20

7.0

CONTROLLER

NETWORK .................................................................................. 21

7.1

MODBUS Configuration ..................................................................................................... 21

7.2

2800 Series MODBUS Register Mapping .......................................................................... 22

8.0

MAINTENANCE .................................................................................................... 23

9.0

TROUBLESHOOTING .......................................................................................... 24

10.0

FLOW

CHARTS .................................................................................................... 26

TABLE OF FIGURES

FIGURE 1 – TYPICAL INSTALLATION .............................................................................. 8

FIGURE 2 – PROBE INSTALLATION ............................................................................... 12

FIGURE 3 – CONTROLLER OVERVIEW .......................................................................... 13

Summary of Contents for 2880R-LT





























Search results

Summary of Contents for 2880R-LT

Reviews:

Related manuals for 2880R-LT

Brands by name

Popular brands

ARJAY ENGINEERING 2880R-LT, User Manual

Search results

Summary of Contents for 2880R-LT

Reviews:

Related manuals for 2880R-LT

Brands by name

Popular brands