manualshive.com logo in svg

Arizona Instrument JEROME 431-X, Operation Manual

Share
Download
Arizona Instrument JEROME 431-X Operation Manual Download Page 5

AZI Customer Service 800-528-7411 or 602-470-1414 

Page 5 of 56

 

1.

 

FOR THOSE WHO CAN'T READ THE WHOLE MANUAL NOW 

 

This manual contains details that will optimize the results and the life of your instrument.  Read 
and refer to the manual for complete details on operation, maintenance and troubleshooting, 
special voltage inputs and data output. 
 
The Jerome

®

 431-X is easy to operate and ready for use upon receipt from the factory.  

•

 

Remove the instrument from the packing material.   

Retain all packaging materials for any future shipment of the 

instrument. 

If the instrument is returned to AZI for any reason, it must be 

placed in the original packaging materials that have been tested 

and proven to be effective protection during shipment.

 

•

 

Call AZI Customer Service at 800-528-7411 or 602-470-1414 for Return Material 
Authorization (RMA) information prior to returning a unit. 

•

 

For all shipments, boxes and packing materials are available from AZI. 

•

 

Pack the Jerome

®

 instrument only in a Jerome

®

 shipping container. 

AZI WILL NOT BE RESPONSIBLE FOR SHIPPING DAMAGE. 

IF YOU RETURN THE INSTRUMENT IMPROPERLY PACKAGED OR 

SHIPPED,  

YOU SHOULD INSURE IT FOR FULL VALUE. 

 

•

 

Check for any damage and confirm receipt of all parts on 
your packing list.  Contact Arizona Instrument Customer 
Service at (800) 528-7411 or (602) 470-1414 if you have 
any questions. 

•

 

Press the ON button.  The display should read 000 in less 
than one second. 

 

A LO BAT message appears briefly in the upper left 
corner. 

 

If the LO BAT message persists, recharge the battery. 
See page 17. 
 
 

•

 

Check the voltage setting (110 or 220 VAC) on the back of the 
instrument.  Ensure that it is set to the correct voltage.  If the 
pointer is not aligned to the local voltage, turn the selector to 
point to the correct voltage. 
 
 
 
 
 

Summary of Contents for JEROME 431-X

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands