manualshive.com logo in svg

Arizona Instrument JEROME 431-X, Operation Manual

Share
Download
Arizona Instrument JEROME 431-X Operation Manual Download Page 19

AZI Customer Service 800-528-7411 or 602-470-1414 

Page 19 of 56

 

Flow System 

 
The Jerome

®

 431-X's flow system is the crucial link between the sensor and the sample.  For the 

instrument to perform correctly, the flow system must be properly maintained.  The user 
maintainable components of this system are the intake filter (.25 inch fritware), a C/M Filter, two 
scrubber filters and connecting tubing. 
 
Check the Preventive Maintenance Calendar on page 18, for a suggested schedule for changing 
fritware and scrubber filters.  The Tygon™ tubing in the system must be free of crimps for 
proper flow. 

 

Part

 

Part Number 

Scrubber Filter 

Z2600 3930 

C/M Filter 

Z2600 3928 

.25 inch Fritware Filter 

2600 3039 

Tygon™ Tubing - 1/8" I.D. (1') 

2500 3001 

 

.25 inch Fritware Filter 

 

Replace the .25 inch fritware filter once each week or as needed.  In dusty environments, the 
fritware filter may need to be replaced as often as once a day.  Replacement .25-inch fritware 
filters are available from AZI, Consumable Sales at 800-528-7411 or 602-470-1414. 

•

 

Unscrew and remove the intake.  

 
 

•

 

Push the old fritware filter disc out of the intake with your 
trimmer tool. 

 

•

 

Avoid touching the new fritware disc with fingers.  Use 
tweezers to insert the new fritware. 

•

 

Use the blunt end of the trimmer tool to seat the fritware disc 
firmly against the inner ledge of the intake. 

•

 

Screw the intake back on the Jerome

®

 431-X. 

 

CAUTION: 

The stem coming from the instrument onto which the outer intake housing 
is attached must be securely held in place.  If loose, the tubing inside the 
instrument can become twisted when the intake housing is replaced.  It may 
be necessary to open the instrument and tighten the hold-down nuts inside 
the instrument.  Call AZI Customer Service at 800-528-7411, 602-470-1414, 
or e-mail [email protected] if you have any questions 

Summary of Contents for JEROME 431-X

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands