background image

ARITERM SWEDEN AB 

 ARITERM OY

 

• Asennus ja käyttöohje • Installation och driftanvisning • Installation and operating instruction • 19.11.2009 • 19/32

 GUARANTEE AND DECOMMISSIONING

 

MOST COMMON SPARE PARTS

 Guarantee

Ariterm Oy gives a two-year guarantee on the boiler starting from the date of installation. The 
guarantee covers the faults related to work and raw materials that may appear in the boiler. The 
manufacturer assumes no guarantee liability if the defect has been caused by an installation 
fault, leaks outside the boiler, faulty operation, freezing, overheat or overpressure. If the repair 
operations have been started without the manufacturer's permission or the guarantee card has 
not been returned to the factory, the guarantee is not valid. The factory is not responsible for 
the possible consequential damages and costs caused by the boiler. Ariterm Oy reserves the 
right to decide the way in which the guarantee repair is carried out. Ariterm Oy is not liable 
for damages occurred after the expiration of the guarantee period. However, compensation for 
such damages may be separately agreed on a case-by-case basis.

 

Decommissioning

An end-of-life boiler is suitable for scrapping. Its plastic parts are landfill waste.

Product no.

Description

1163

Overheat protection EGO 55.33412.010

1774

Gasket 2x183x200, burner

5660

Grundfos UPS 25-40 pump

13245

Boiler temperature sensor

13249

Flue gas temperature sensor

13257

BeQuem 20 inner cage

13721

Display card Bm+/BQ

14048

ESBE ARA661 shunt motor

14054

Sweeping motor SPG TS09-0175

14059

Controller card B

14066

Outdoor temperature sensor

14067

Indoor temperature sensor

14067

Supply water sensor

1136

Chain wheel Z=12

13197

Hub chain wheel Z=15

13198

Hub chain wheel Z=24

1138

47-link chain

1139

Chain shackle

10667

Feed motor SPG S8I15GXCE/S8KA180M

13183

Internal casting of the burner head

13184

Internal casting of the burner head

13187

Blocking feeder

13192

Auger burner 

13356

Blower SUO78613

13199

Ignition resistance 450W 

10669

Level switches (incl. transmitter and receiver)

10668

Optical flame switch

Summary of Contents for Biomatic+

































Reviews: