manualshive.com logo in svg

Aritech 1X-F Series, Operation Manual

Share
Download
Aritech 1X-F Series Operation Manual Download Page 28

 

22 

1X-F Series Operation Manual 

Testing sounders (or evacuation for NBN S 21-100) 

To test sounders (or evacuation for NBN S 21-100), press the General Test 

button, and then press the Sounder Fault/Disable/Test button (or Evacuation 

Fault/Disable/Test button for NBN S 21-100).  
Sounders (or evacuation for NBN S 21-100) can only be tested when the control 

panel is in standby state. 
The test is indicated as follows: 
•  General Test LED: On steady. 
•  Sounder Fault/Disable/Test LED (or Evacuation Fault/Disable/Test LED for 

NBN S 21-100): On steady. 

•  The sounders (or evacuation for NBN S 21-100) emit the audible test signal 

(3 seconds on, 5 seconds off) for the duration of the test, without any 

configured delay. 

To end the test, press the General Test button, and then press the Sounder 

Fault/Disable/Test button (or Evacuation Fault/Disable/Test button for 

NBN S 21-100) again. 
If there is a fire alarm the fire panel will exits the test and responds to the alarm 

as configured. 

Disabling sounders or enabling sounders (or evacuation for NBN S 21-100) 

To disable sounders (or evacuation for NBN S 21-100), press the General 

Disable button, and then press the Sounder Fault/Disable/Test button (or 

Evacuation Fault/Disable/Test button for NBN S 21-100). 
Disabled sounders (or evacuation for NBN S 21-100) are indicated as follows 
•  General Disable LED: On steady. 
•  Sounder Fault/Disable/Test LED (or Evacuation Fault/Disable/Test LED for 

NBN S 21-100): On steady. 

To enable the sounders, press the General Disable button, and then press the 

Sounder Fault/Disable/Test button (or Evacuation Fault/Disable/Test button for 

NBN S 21-100) again. 

Note: 

Disabled sounders (or evacuation for NBN S 21-100) do not indicate a 

fault or operate if there is a fire alarm. 

Summary of Contents for 1X-F Series


































Reviews:

No comments

Brands by name

Popular brands

Load more brands