manualshive.com logo in svg

ARIS TENSOR, Original Declaration Of Incorporation With Manual

Share
Download
ARIS TENSOR Original Declaration Of Incorporation With Manual Download Page 24

24

Tensor

7.2 

Setup mode I-ACT (PMR)

1.  Slide switch to MANU (2).
2.  Hold down button MENU (3) at least 2 seconds.

The left point flashes. The controller stands in the 1. menu level and waiting for further commands.

Survey

The microprocessor controller I-ACT (PMR) can perform the following tasks:
• 

Set left and right end position

• 

Set handling shortly before reaching an end position and switching on and off of the motor

• 

Enter voltage and current values for the end positions

• 

Activate message output

Buttons and switches

In the setup mode the buttons have different functions in the three menu levels. The two points display the menu level, in which the 
controller is currently working.

By changing the switch from manual to automatic the setup mode is left without saving a 
currently revised parameter value.

Start setup mode

1.  Slide switch to „MANU“.
2.  Hold down button [M] at least 2 sec.
 
The setup for parameter setting is turned on, the display shows the first menu item.

E

.

L

 

Setup mode active, 1. menu level in display.

To exit the programming mode, slide switch back to "AUTO".

ADVICE

!

Summary of Contents for TENSOR

































Reviews:

No comments

Brands by name

Popular brands

Load more brands