Argal ASTRA Evo DDE 030 Operator And Maintenance Manual Download

Page: 31 / 62

Operations & maintenance manual – ASTRA evo (DDE)

ARGALAIR 2020 | Rev. 6

The pump stalls

Suction pipe clogs during operation

Replace the suction pipe

Dirty air, full of condensate or oil

Check the air line. Follow the indications within
the use manual

Insufficient air volume or pressure

Check the pressure with a gauge installed on
the pump and with running pump. If pressure in
that point is too low related to the mains
pressure, check all the air connections. Check
that all the air control devices have a sufficient
flow rate

Defective pneumatic exchanger

Replace pneumatic exchanger

The stop procedure was not

respected

Respect the stop procedure

Liquid leaks from the pump

Screws on the fluid chamber not

properly tightened

Check tightening torques of the screws

O-rings on manifolds damaged

Replace O-rings

Damaged diaphragms

Check / replace diaphragms

The pump does not deliver
the flow rate indicated on the table

Suction or air connection blocked

Check / clean air supply / suction connection

The product suction pipe is not

correctly connected or not correctly
dimensioned

Check the suction line

Clogged pipes

Check and clean

Too viscous fluid

Install pipes with greater size especially for
suction and decrease the pumps cycles

Valve balls do not close / Valve seats
are worn

Disassemble the manifolds and clean the seats
or replace the balls and the seats if worn

Insufficient air volume

Diaphragms breakdown

Check / replace diaphragms

Icing on the silencer

Improve the air quality

Pressure losses on suction side

Check / change installation on suction side

Pressure fall in air supply

Increase the air pressure via a filter-regulator

Diaphragms breakdown

Pressure too high during installation

Use a protective treatment system /
air regulation (follow the use manual)

Dry running of the pump for long

periods

Run the pump slowly if not filled with fluid (dry
running case) – follow the instructions within
use manual

Pressure too high on suction side

Make sure there is a pressure balance
between the air side and the fluid side of the
diaphragm

10 Leakage of fluid from the silencer

Diaphragms breakdown

Check / replace diaphragms

Table 6

Summary of Contents for ASTRA Evo DDE 030































































Search results

Summary of Contents for ASTRA Evo DDE 030

Reviews:

Related manuals for ASTRA Evo DDE 030

Brands by name

Popular brands

Argal ASTRA Evo DDE 030, Operator And Maintenance Manual

Search results

Summary of Contents for ASTRA Evo DDE 030

Reviews:

Related manuals for ASTRA Evo DDE 030

Brands by name

Popular brands