Ares AZSA3000 Quick Start Manual Download Page 4

QUICK-START GUIDE

Full manual available to download from: www.Ares-RC.com

11

Insert the wing bolt and push it 

firmly down to lock it in position. 

A firm twist in either direction will 

release it.

12

Read and fully understand the LiPo 

care and safety precautions in the 

full online manual at www.Ares-RC.

com and never leave LiPo batteries 

unattended whilst charging. Plug 

the mains power adaptor into a wall 

socket and connect the charger to 

the power adaptor using the circular DC socket. Switch the wall unit on and 

note that the green LED ‘Power’ indicator on the charger will light.

13

Place the charger on a flat, 

heat-resistant surface with a 

good airflow all around. Connect 

the supplied 3S 2200mAh Li-Po 

battery to the charger using the 

white three pin balance plug, 

taking care to ensure its correct 

orientation. The red ‘Charger’ LED 

will light indicating that the battery is charging. When fully charged the red 

LED will stop glowing, whereupon the battery can be disconnected.

14

Open the battery hatch on the 

underside of the fuselage, insert 

the LiPo and slide it as far forward 

as it will go.

To attach the wing to the fuselage 

locate the dowels at the leading 

edge then insert the wing bolt 

plate at the trailing edge to pull the 

two halves together.

10

Summary of Contents for AZSA3000













Reviews: