manualshive.com logo in svg

Arctic Spas Arctic Fox, Owner'S Manual, Page: 12 / 124

Share
Download
Arctic Spas Arctic Fox Owner'S Manual Download Page 12

Owners Manual - Arctic Spas®

Electrical Specifications

Electrical Installation Instructions

DANGER!

Shock Hazard.

DO NOT PROCEED if

you are not a licensed 

electrician

.

 This

diagram is for

reference only!

ARCTIC SPAS® MUST BE WIRED IN ACCORDANCE WITH ALL

APPLICABLE LOCAL ELECTRICAL CODES. ALL ELECTRICAL WORK SHOULD BE 

DONE BY AN EXPERIENCED, LICENSED ELECTRICIAN

AND APPROVED BY A LOCAL BUILDING/ELECTRICAL 

INSPECTION AUTHORITY. 

The electrical supply must satisfy the requirements of the spa as marked on the certification label which is 

located adjacent to the spa controller (pack). If the ratings are not legible or cannot be found,  please contact 

the factory for assistance. - DO NOT GUESS!

WARNING:

 

Removing or bypassing any GFCI /RCD breaker will result in an unsafe  

 

         spa and will void the spa’s warranty.

IMPORTANT: Your Arctic Spa has been carefully engineered to provide maximum

                       safety against electric shock. Remember, connecting the spa to an

                       improperly wired circuit will negate many of its safety features.

12

12

Summary of Contents for Arctic Fox





























































































































Reviews:

No comments