61
Problem: Engine noisy (Noise seems to come from secondary-transmission/right-side cover)
Condition Remedy
1.
Gears - shaft(s)
worn
2.
Bearing(s)/bushing(s)
damaged
1. Replace gears - shafts
2. Replace bearing(s)/bushing(s)
Problem: Engine noisy (Noise seems to come from secondary bevel gear and final driven shaft)
Condition
Remedy
1.
Drive - driven bevel gears
damaged - worn
2.
Backlash
excessive
3.
Tooth contact
improper
4.
Bearing
damaged
5.
Gears
worn - rubbing
6.
Splines
worn
7.
Final driven shaft thrust clearance
too large
1. Replace gears
2. Adjust backlash
3. Adjust contact
4. Replace bearing
5. Replace gears
6. Replace shaft(s)
7. Replace thrust washer(s)
Problem: Centrifugal clutch slipping
Condition Remedy
1.
Clutch shoes
worn
2.
Clutch housing
excessively worn
3.
Drive belt
slipping - worn
1. Replace shoes
2. Replace clutch housing
3. Replace drive belt
Problem: Secondary-transmission will not shift or shift back
Condition Remedy
1.
Sliding dog
broken - worn
2.
Gearshift fork
broken - worn
3.
Hi/Low shift lever
out of adjustment
4.
Gearshift cam
worn
5.
Cam stopper spring
weak
6.
Gearshift fork shaft
worn
7.
Engine idle
too high
8.
Shift linkage
out of adjustment
1. Replace dog
2. Replace fork
3. Adjust lever
4. Replace cam
5. Replace spring
6. Replace shaft
7. Adjust engine idle
8. Adjust shift linkage
Problem: Engine idles poorly
Condition
Remedy
1.
Valve clearance
out of adjustment
2.
Valve seating
poor
3.
Valve guides
defective
4.
Rocker arms - arm shaft
worn
5.
Magneto
defective
6.
CDI unit
defective
7.
Spark plug
fouled - gap too wide
8.
Ignition coil
defective
9.
Float
out of adjustment
10.
Jets
obstructed
11.
Pilot screw
setting improper
1. Adjust clearance
2. Replace - service seats - valves
3. Replace guides
4. Replace arms - shafts
5. Replace magneto
6. Replace CDI unit
7. Adjust gap - replace plug
8. Replace ignition coil
9. Adjust float height
10. Clean jets
11. Adjust pilot screw
Problem: Engine runs poorly at high speed
Condition
Remedy
1.
High RPM “cut out”
against RPM limiter
2.
Valve springs
weak
3.
Valve timing
out of adjustment
4.
Cams - rocker arms
worn
5.
Spark plug gap
too narrow
6.
Ignition coil
defective
7.
Float level
too low
8.
Air cleaner element
obstructed
9.
Fuel hose
obstructed
1. Shift into higher gear - decrease speed
2. Replace springs
3. Adjust timing
4. Replace cams - arms
5. Adjust gap
6. Replace ignition oil
7. Adjust float height
8. Clean element
9. Clean - prime hose
Problem: Exhaust smoke dirty or heavy
Condition
Remedy
1.
Oil (in the engine)
overfilled - contaminated
2.
Piston rings - cylinder
worn
3.
Valve guides
worn
4.
Cylinder wall
scored - scuffed
5.
Valve stems
worn
6.
Stem seals
defective
7.
Air cleaner element
obstructed
8.
Float level
too high
1. Drain excess oil - replace oil
2. Replace - service rings - cylinder
3. Replace guides
4. Replace - service cylinder
5. Replace valves
6. Replace seals
7. Clean element
8. Adjust float level
Manual
Table of Contents
For Arctic Cat Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
