Arctic Cat ATV 300 DVX Operator'S Manual Download

Page: 43 / 84

Divis

ion

- Opera

tion

inte

nance

ATV Operation

1. Use the ATV’s momentum to clear

the obstacle.

2. Don’t pull up on the handlebar.
3. Don’t apply the throttle.

Driving an ATV and a car have some

similarities; however, there are a few sit-

uations that require special attention:

• Reversing
• Skidding or Sliding
• Parking on a Hill
• Stalling on a Hill
• Crossing Water
• Crossing Roads
• Cold Weather Driving
• Stopping the ATV
• Stopping the Engine

Reversing

It’s tough to see things behind you.

1. Go slowly. It’s hard to see behind

you.

2. Keep your handlebar straight.
3. Backing down hills is a bad idea; do

a U-turn or K-turn instead to turn

around.

Skidding or Sliding

If you lose control after hitting sand, ice,

mud, or water:

1. Turn your handlebar into the direc-

tion of the slide.

2. Keep your hand off the brakes until

you’re out of the skid.

3. Shift your weight forward.

Sometimes your ATV may not respond

and goes straight ahead instead of letting

you turn. Here’s how to handle it:

1. Slow down.
2. Move forward on the seat.
3. Lean to inside of turn.
4. Turn handlebar.

Parking on a Hill

This shouldn’t be necessary, but if it is:

1. Keep it in gear.

2. Engage the brake lever lock.
3. Find something to block the rear

tires.

Stalling on a Hill

If you use the right method for riding

uphill, this shouldn’t happen. But if you

have a problem, do this:

1. If the ATV hasn’t started rolling

backwards yet, follow the proce-
dure for the K-Turn,

2. If the ATV is already rolling back-

ward, lean as far forward as possible

standing up on the footrests.

3. Nice and easy, apply the front and

rear brakes.

4. When you come to a stop, follow the

procedure for the K-turn.

5. If the ATV continues to roll back-

ward, dismount immediately on the

uphill side.

Crossing Water

Your ATV can only handle water up to its

footrests. Any more than that and you

risk engine damage and/or personal

injury. Stay away from fast moving riv-

ers. ATV tires can be buoyant, so if the

water is too deep, you might find the

ATV suddenly afloat.

1. Physically check the depth and cur-

rent of the water, especially if you

can’t see the bottom. You’re also

checking for boulders, logs, or any

other hidden obstacles.

2. Keep your speed slow.
3. Make sure you have a way out on

the other side of the water.

4. If you get stuck in the sludge or

mud, try rocking the ATV from side

to side.

5. Once you’ve cleared the water,

briefly apply the brakes to make sure

they work.

Crossing Roads

Crossing roads on your ATV is also a bad

idea, so avoid it. If you can’t:

Tips

Summary of Contents for ATV 300 DVX





















































































Search results

Summary of Contents for ATV 300 DVX

Reviews:

Related manuals for ATV 300 DVX

Brands by name

Popular brands

Arctic Cat ATV 300 DVX, Operator'S Manual

Search results

Summary of Contents for ATV 300 DVX

Reviews:

Related manuals for ATV 300 DVX

Brands by name

Popular brands