manualshive.com logo in svg

Arcom RC210, Operation Manual, Page: 21 / 68

Share
Download
Arcom RC210 Operation Manual Download Page 21

 

21 

 

Port Unique Versus Global Programming 

There are two types of programming commands: 

Those that affect only the port you currently have unlocked. These are referred to 

as Port Unique Programming Commands

, which may 

be done from any radio port. In other words, you can program Port 2 while actually using a radio connected to Port 1. 

 Those commands which are shared between all ports or don't apply to a specific port. These are referred to as 

Global commands

. For 

example, reading an ADC channel or controlling a remote base radio. 

 

Port Unique Programming 

Timer Programming 

Unless otherwise noted, all of the following commands may be programmed with only those digits necessary. In other words, if the 
value you wish to enter is "20", you need only enter "20". If you want to enter "1234", you simply enter "1234" for that programming 
command.

 

Hang Time

 

Each port has its own programmable hang time when that port is configured for full-duplex operation (in half-duplex, there is no hang 
time).  It is programmed in 1/10 second intervals. For example, 1 second would be programmed with a value of "10".  

*1000x

 where "x" is the amount of hang time for that port's transmitter in 1/10 seconds. The range is 0 to 25.5 seconds. The controller 

responds with "H A N G TIMER SET". 

Note: setting the timer to 0 gives zero hangtime 

 

Time Out Timer

 

Each port is provided with a time out timer that will drop the transmitter should a signal appear on its receiver input for longer than the 
programmed time out period (this only applies if that port is in full-duplex).  

*

1001x

 where "x" is the time out period for that port's transmitter in seconds. The range is 1 to 32767. The controller responds with 

"TIMEOUT SET".  

Note: Setting the timer to zero disables it.

 

Initial ID Timer

 

This timer sets the amount of time the repeater must be idle before sending the Initial ID. For example, if you set this timer to 10 
minutes and that port is in full-duplex and unused for at least 10 minutes, this ID will play upon initial keyup. It won't play again until the 
repeater sits idle for another 10 minutes. 

*1002x

 where "x" is the amount of time in minutes between ID's. The default time is 10 minutes and there is really no need to change it, 

but it can be changed from 1 to 255 minutes. The controller responds with "IID TIMER SET". 

NOTE: You may disable ID’s completely on any Port by programming a value of 0 for the Initial ID Timer. You will usually want 
to do this on a Port not set as a repeater Port. 

 

Pending ID Timer

 

After the initial ID is sent, the Pending ID timer is started. While this timer is running, if during this time there is activity on that port, the 
Pending ID message will be sent. If activity continues, the Pending ID will be sent every period, programmed by its timer. If there is no 
activity after the initial keyup, no further IDs are sent until the Initial ID period has elapsed. Also see the Pending ID Speech Timer 
below for more information on how this works. 

*1003x

 where "x" is the amount of time in minutes the Pending ID waits after an Initial ID occurs. The default is 10 minutes and there is 

really no need to change it, but it can be changed from 1 to 255 minutes. The controller responds with "PID TIMER SET". 

Summary of Contents for RC210





































































Reviews:

No comments