Arcom Digital Quiver XT User Manual Download Page 64

Page: 64 / 80

Sweep Profiles

The Quiver -XT SSG feature allows the

operator to select two types of sweep profiles;
Fixed and manual

A manual sweep profile gives the technician

sixteen fully configurable frequency points that
can set as required.

64-point Fixed sweep profiles can be installed

through the Q-browser program revision 5.0.0.11
and above and selected by the user as required.

Manual sweep profile

Manual sweep profile offers an on-site

configurable sweep pattern that can be changed
at any time. Output level, sweep time and markers
are also configurable.

1.TX Level

: Select this option to change the

output from +10 to +35 dBmV

2.Sweep freqs

: Select this menu option to

adjust 16 frequency points between 5 and 90
MHz.

Sweep time

: Allows you to adjust the sweep

time from 5mS to 10 mS.

Markers

: allows the technician to use two 1 or

2 markers. Markers can be set to Maximum peak,
manual adjustment (<>), or off.

Summary of Contents for Quiver XT

















































































Search results

Summary of Contents for Quiver XT

Reviews:

Brands by name

Popular brands

Arcom Digital Quiver XT, User Manual

Search results

Summary of Contents for Quiver XT

Reviews:

Brands by name

Popular brands