manualshive.com logo in svg

Arcom Digital Quiver XT, User Manual

Share
Download
Arcom Digital Quiver XT User Manual Download Page 3

 

 

 

3

 

Spectrum analyzer/Signal level meter modes ............................................................................. 35

 

Return spectrum analyzer mode ................................................................................................... 35 

LNA – low noise amplifier ............................................................................................................. 37 

Reference level change ................................................................................................................. 37 

Scale change .................................................................................................................................. 38 

Markers ......................................................................................................................................... 39 

Using Max Hold ............................................................................................................................. 40 

Hold feature .................................................................................................................................. 41 

Saving a Spectrum Analyzer Trace ................................................................................................ 41 

Forward SLM/Spectrum mode .................................................................................................... 43

 

Examples of actual FWD spectrum signals .................................................................................... 43 

QAM demodulator mode ........................................................................................................... 45

 

Using the Save Trace Option ....................................................................................................... 46

 

Saving a Trace ................................................................................................................................ 46 

Recalling a Trace ............................................................................................................................ 47 

Clearing Traces .............................................................................................................................. 48 

Downloading Traces ...................................................................................................................... 48 

Using CPD Radar in Headend View ............................................................................................... 49 

Calibrator Mode (QVR-XT only) .................................................................................................. 50

 

Calibrator Connection Diagrams ................................................................................................. 51

 

Nodes ............................................................................................................................................ 51 

Alternative Node Calibration ........................................................................................................ 52 

Using Calibrator mode ............................................................................................................... 53

 

Setting Up the Data Carrier Frequency ......................................................................................... 54 

Setting the Signal Output Level ..................................................................................................... 56 

Calibrating a Fiber Node ................................................................................................................ 57 

Turning Calibrator Output Signal ON and OFF .............................................................................. 57 

Leakage Detector ....................................................................................................................... 60

 

Max Hold leak level ....................................................................................................................... 62 

Saving and recalling the leakage trace .......................................................................................... 63 

RTN Simple Sweep Generator ..................................................................................................... 63

 

Sweep Profiles ............................................................................................................................... 64 

Manual sweep profile ................................................................................................................... 64 

Fixed sweep profile ....................................................................................................................... 65 

Creating a fixed sweep profile. ..................................................................................................... 65 

Transferring a fixed sweep profile using Q-browser. .................................................................... 66 

Quiver Navigator App ................................................................................................................ 67

 

Loading maps into your Quiver Navigator App ............................................................................. 67 

QR Codes ................................................................................................................................... 69

 

Using the QR Code with the Mobile Quiver Navigator App. ......................................................... 71 

Changing the Quiver-XT Battery Pack   .................................................................................... 76

 

Changing the Q-AMP Battery   ................................................................................................ 77

 

Quiver-XT-UB Specifications ....................................................................................................... 78

 

Physical .......................................................................................................................................... 78 

Environmental ............................................................................................................................... 78 

Interfaces ...................................................................................................................................... 78 

Summary of Contents for Quiver XT

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands