ARCIMOTO FUV 2022 Owner'S Manual Download Page 80

Page: 80 / 194

page 78

FUV Owner's Manual (REV 0) • last revised: 3/31/2022 • part# 006290 • docID: P10001

Display Brightness

The

brightness

the

Display

and

Control

Panel

automatically dims when the headlights are switched
from DAY MODE to NIGHT MODE.

Refer to the

Headlights Switch section on page 47

for

details on using the headlights.

There are two modes of brightness for the Display:

Brightness Day

(headlights set to DAY MODE): By

default, the Display is at full brightness, suitable for
daytime driving.

Brightness Night

(headlights set to NIGHT MODE -

LOW BEAM or NIGHT MODE - HIGH BEAM): By
default, the Display dims for typical nighttime
driving.

The brightness setting for each of these modes can be
adjusted via the

Brightness Day

and

Brightness Night

settings on the Configuration page:

Adjusting the Display Brightness Settings

To adjust the Display brightness for DAY MODE:

1. Set the Headlight Switch on the left grip to DAY

MODE.

2. Select a Display brightness level for DAY MODE by

selecting one of the four settings under

Brightness

Day

Once set, the Display will use the selected
brightness level when the Headlight Switch is
in DAY MODE.

DISPLAY

Summary of Contents for FUV 2022



































































































































































































Search results

Summary of Contents for FUV 2022

Reviews:

Related manuals for FUV 2022

Brands by name

Popular brands

ARCIMOTO FUV 2022, Owner'S Manual

Search results

Summary of Contents for FUV 2022

Reviews:

Related manuals for FUV 2022

Brands by name

Popular brands