ARCIMOTO FUV 2022 Owner'S Manual Download

Page: 40 / 194

page 38

FUV Owner's Manual (REV 0) • last revised: 3/31/2022 • part# 006290 • docID: P10001

Once the green check mark displays for the brake pedal,
squeeze the Startup button on the left grip:

This will update the screen again, with a green check mark
replacing the Startup Button graphic:

Once the FUV is started, release the START button.

At this point, the FUV is started and is ready to drive.

However, it is important to follow the four steps listed on

the screen under "

Before Driving

Turn off parking brake:

Check the Parking Brake button

on the Control Panel. If the LEDs on the button are lit, then

the Parking Brake is ON.

GETTING STARTED

Summary of Contents for FUV 2022



































































































































































































Search results

Summary of Contents for FUV 2022

Reviews:

Related manuals for FUV 2022

Brands by name

Popular brands

ARCIMOTO FUV 2022, Owner'S Manual

Search results

Summary of Contents for FUV 2022

Reviews:

Related manuals for FUV 2022

Brands by name

Popular brands