Architectural Area Lighting Y-LED Installation Manual Download Page 35 | Manualshive

Page: 35 / 37

Architectural Area Lighting Y-LED Installation Manual Download Page 35

93039741

FGL-LED

01/6/12

A

INSTALLATION INSTRUCTIONS

CATALOG NUMBER

PART NO.

APPRVD

DATE

DATE

REV.

16555 East Gale Avenue

City of Industry, CA 91716-0080

(626)968-5666 Fax(626)330-3861

01/10/12

K.CHUK

(4) STAINLESS STEEL
SET SCREWS

FITTER-LARGE
(REF)

LID-LARGE

LATCH

QUICK
DISCONNECT

QUICK
DISCONNECT

LENS

EMITTER
ASSEMBLY

5" O.D POLE

FIXTURE INSTALLATION STEPS:

1) TURN POWER OFF.
2) MAKE WIRE CONNECTIONS FROM
    INCOMING SUPPLY TO FIXTURE ASS'Y.
    (NOTE: FIXTURE ASSEMBLY MUST BE
    GROUNDED TO INCOMING EQUIPMENT
    GROUND SUPPLY).
3) SLIP FITTER OVER TOP OF POLE. SECURE
    FITTER WITH (4) STAINLESS STEEL SET SCREWS.
4) INSTALLATION COMPLETE.

WARNING:

THIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE
STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH
DEFECTS, AND/OR OTHER REPRODUCTIVE HARM.
THROUGHLY WASH HANDS AFTER INSTALLING,
HANDLING, CLEANING OR OTHERWISE TOUCHING THIS
PRODUCT.

WIRE CONNECTORS
(BY OTHERS)

FINIAL

BALLAST
ASSEMBLY

1/4-20 SCREW

TO SERVICE BALLAST:

1) INSERT FINGER BEHIND LATCH LOCATED AT
    SIDE OF THE FIXTURE AND PULL LATCH
    FORWARD AND LIFT TOP LID OPEN.
2) DISCONNECT QUICK DISCONNECT.
3) REMOVE 2 X 1/4-20 SCREWS AND LOWER
    BALLAST ASSEMBLY.
4) SERVICE BALLAST AS NEEDED.
5) TO RE-ASSEMBLE, REVERSE INSTRUCTIONS.

«
...
33
34
35
36
37
»

Summary of Contents for Y-LED






































Reviews:

No comments