Arcam DiVA DT81 Handbook Download

Page: 6 / 12

DT81

Using your tuner

Front panel controls

Power

Switches the unit on and off. When off the status LED shows
red. When the tuner is switched on the status LED shows
green.

Searching for services

When using the tuner for the fi rst time we recommend that
you perform a search to fi nd all available services in your
area. Once you have done this, you may wish to repeat a
search periodically to discover if any new ensembles (groups
of services) have gone on air. If you move to another area you
should also perform a new search.

Selecting a search region

Access the ‘Search Region’ menu by pressing the

MENU

button

three times. Use the rotary controller to select the world
region that best describes your location; the options are UK,
Canada or Rest of World. When the desired region is displayed,
press

SELECT

. The tuner takes a few seconds to reconfi gure

its internal software before automatically switching out of the
Search Region menu. You should now perform a search for
available services.

To perform a search

Press

SEARCH

on the front panel, then

SELECT

when

prompted. A bar graph will show the progress of the search.
This can take up to three minutes depending on the search
region you have selected. The search can be cancelled at any
time by pressing any front panel button or rotating the rotary
controller.

If no service is found after the search then either your aerial
is insuffi cient for your location or, you may be outside of the
covered area for DAB services. If this is the case contact either
your Arcam dealer or Arcam customer services.

Selecting a service

Turn the rotary controller to scroll through the available
services and choose the one you wish to listen to.

What happens next depends on the setting of the Selection
mode (see page 7). If set to ‘Auto’, the displayed service
is selected after 2.5 seconds; if set to ‘Manual’, the display
returns to the current service after fi ve seconds unless

SELECT

is pressed.

is shown in the top right corner of the display when

a service is selected, a secondary service is also available.
Moving the rotary controller clockwise one more click will
display this secondary service: press

SELECT

to listen to it.

Programming a preset

First select the service you wish to assign to a preset. Now
press

STORE 1–8

STORE 9–16

and then briefl y press the

appropriate preset button to store the service.

It is not possible to assign secondary services to presets, only
primary ones, since secondary services are often broadcast on
a temporary basis and they may change from day to day.

Selecting a preset

To select presets

, press and release the corresponding

button. To select presets

, press and hold the

corresponding button for two seconds.

Changing the display mode

The bottom line of the display can be set to one of four modes:
Programme type (a brief label), Dynamic label (scrolling text),
Data rate (shows service data rate and stereo/mono mode)
and Signal quality meter (a bar graph). See page 7 for further
information.

Press

DISPLAY MODE

to cycle through the modes.

Compression mode

Press the

MENU

button once to access the compression menu.

From this, dynamic range compression (DRC) can be applied to
the audio signal within the tuner, provided the broadcaster has
made it available for that service. The amount of compression
is adjustable between ‘off’ and ‘5’ (the maximum amount).

To set the compression level, turn the rotary controller until the
required compression level is displayed and press

SELECT

. The

tuner leaves the compression menu and displays the service
name. ‘C1’ to ‘C5’ is shown in the top right corner of the
display, according to the compression level selected.

To exit this menu without making any changes, press the

MENU

button until the tuner reverts to displaying the service name.

Note that the selected level of compression is applied to all
services where compression data is made available by the
broadcaster. It is not possible to store different compression
levels for different stations.

Service sort menu

Services can be sorted by name or by programme type. To
change between ‘sort by name’ and ‘sort by programme type’,
press the

MENU

button twice to access the Service Sort menu

and turn the rotary controller. Press

SELECT

to confi rm the

setting: the tuner reverts to displaying the service name.

To exit this menu without making any changes, press the

MENU

button until the tuner displays the service name.

POWER