background image

 

DEC 2001 

Page 1 of 6 

3782513

 

 

If you have any queries regarding the installation of this product please contact the distributor from whom it was purchased, or alternatively the ARB office in your state. 

Head Office – ARB Corporation Ltd VIC: 42-44 Garden Street, Kilsyth, Victoria, 3137 Tel: (03) 9761 6622 Fax: (03) 9761 6807 

WA: 

(08) 9244 3553  

NSW:

 (02) 9821 3633  

ACT:

 (02) 6280 7475  

SA:

 (08) 8244 5001  

QLD:

 (07) 3872 3872  

NT:

 (08) 8947 2262  

TAS:

 (03) 6331 4190

 

 
LAND ROVER DISCOVERY  

No 32/3432050 

 
DELUXE AND WINCH BULL BARS  

 

(JANUARY 1995 ONWARD) 

 

 
 

WARNING 

FOR VEHICLES EQUIPPED WITH SRS AIRBAG 

WHEN INSTALLED IN ACCORDANCE WITH THESE INSTRUCTIONS, THE FRONT 

PROTECTION BAR DOES NOT AFFECT OPERATION OF THE SRS AIRBAG. 

 

TAKE NOTE OF THE FOLLOWING: 
 

 

THIS PRODUCT MUST BE INSTALLED EXACTLY AS PER THESE 
INSTRUCTIONS USING ONLY THE HARDWARE SUPPLIED. 

 

 

DO NOT USE THIS PRODUCT FOR ANY VEHICLE MAKE OR MODEL, 
OTHER THAN THOSE SPECIFIED BY ARB. 

 

 

DO NOT REMOVE LABELS FROM THIS BULL BAR. 

 

 

THIS PRODUCT OR ITS FIXING MUST NOT BE MODIFIED IN ANY WAY. 

 

Summary of Contents for 3432050







Reviews: