background image

II INSTALLATION

- Protect the  electrical circuit to the pump by a 30mA RCD, ensuring  the  proper  grounding  of 

your installation. if in doubt consult  a  qualified professional. 

- Position the pump horizontally at 3.50 m over the basin, below the level of water in a dry, well 

ventilated, protected from rain. Leave a space of 30 cm behind the fan cover.- Ensure the accessibi-

lity of the strainer basket for regular cleaning. 

- Set the pump on a solid base (concrete base filter, plank) using 2 screws adapted (not included). 

- Set up the connections (not supplied) 1’’1 / 2 32-38 mm (Ref 200237 EAN13 : 3359192002376), 

using PTFE tape. 

- Install the suction and discharge of the pool by limiting the lengths and bends and avoiding traps. 

It should not produce mechanical stress on the pump. For more comfort we suggest you install the 

valves 1 / 4 turn (Ref : 200406 EAN13 : 335 919 200 4066) on the suction and discharge.

I GENERAL

This manual provides information about the installation, the use and maintenance 

of your pump.

This pump is designed to ensure the flow of clean water and disinfected in a private swimming pool 

filtration circuit. Any other application will invalidate any warranty and / or appeal with the supplier. 

The water temperature should not exceed 35 ° C.

III INSTALLATION OF THE PIPE

- Check that  the  fan cover is well positioned and does  not touch the propeller. 

- Rotate the motor shaft by the fan screws with a screwdriver (the first start and after the rainy 

season). 

- Open the valves of the hydraulic system (if present) to fill to complete the pre-filter the water 

pump. If necessary, remove the lid of the pre-filter and fill with water. Close it by checking the 

correct position of the joint. 

- Plug the pump into the mains. The pump begins in less than a minute. 

- Damage resulting from dry running the pump are not guaranteed.

IV SERVICING

- Check that  the  fan cover is well positioned and does  not touch the propeller. 

- Rotate the motor shaft by the fan screws with a screwdriver (the first start and after the rainy 

season). 

- Open the valves of the hydraulic system (if present) to fill to complete the pre-filter the water 

pump. If necessary, remove the lid of the pre-filter and fill with water. Close it by checking the 

correct position of the joint. 

- Plug the pump into the mains. The pump begins in less than a minute. 

- Damage resulting from dry running the pump are not guaranteed.

A

ctions

d

Aily

Check the clogging of the prefilter

Daily

Clean the prefilter

If dirty

Check the cover gasket

Same cleaning  prefilter

Drain and put in dry

A wintering  pool

Replace the  water level

If less than 2 / 3 of the height of the skimmer after 

the bathing. (heat waves, prolonged absence, etc.)

V MAINTENANCE

C

auses

s

olutions

x

x

x

air entry

Check the tightness of  connections, hose  

and  seal  lid

x

x

Body  of  the  pump without water

Fill the  water  pump housing

x

Hydraulic blocked

Dirty turbine

Clean the skimmer basket, pump prefilter, 

then do a wash against the sand filter.

Requires the dismantling

x

Improper attachment of the pump

Secure properly  ground pump

x

Foreign body  in  the prefilter.

Foreign body  in  the prefilter.

x

No voltage

Reset circuit protection.

x

Axis blocked

See 3.mise  on (cover / Driver)

n

o

 

boo

t

l

o

w

 

flo

w

 

ra

te

u

nusu

al

 

noise

P

um

P

 

does

 

no

t

 

st

ar

t

In other cases, consult your dealer

6

5

HYDRAULIC CURVES

0.0

1.0

2.0

3.0

4.0

5.0

6.0

7.0

8.0

9.0

10.0

11.0

12.0

13.0

14.0

15.0

16.0

17.0

18.0

19.0

20.0

100517
100518
106454
106455
106456

Disconnect the pump before any intervention

Reviews: