background image

313 Regina Avenue • Rahway, New Jersey 07065

Tel: (732) 574-1500 • Fax: (732) 574-1551

www.swimnplay.com • E-mail: [email protected]

Part# 420288-16

GENERAL

INSTALLATION OF THIS ABOVE GROUND POOL IS NOT EXTREMELY HARD OR 
CONFUSING, BUT IT IS A BIG JOB.  THE SECRET TO INSTALLING A POOL SO THAT IT 
WILL GIVE YOU YEARS OF PLEASURE IS TO TAKE THE TIME TO FOLLOW INSTRUCTIONS 
AND DO THINGS RIGHT THE FIRST TIME.  YOUR POOL WARRANTY IS VOID IF THESE 
INSTRUCTIONS ARE NOT FOLLOWED 100%.  READ ALL INSTRUCTIONS INCLUDING 
ACCESSORIES SUCH AS FILTERS, PUMPS, SKIMMERS, DECKS, ETC. PRIOR TO 
STARTING.  ANY AFTERMARKET OR HOME BUILT DECK, IF ALLOWED, SHOULD BE 
CONSTRUCTED ACCORDING TO ALL LOCAL BUILDING CODE REQUIREMENTS, INCLUD-
ING LOAD CAPACITY AND FENCING REQUIREMENTS.

BEFORE YOU START, CHECK TO SEE THAT YOU HAVE THE CORRECT NUMBER OF 
PARTS.  USE YOUR PARTS LIST WHICH IS BROKEN DOWN BY CARTON.

THE MANUFACTURER RESERVES THE RIGHT TO REVISE, CHANGE, OR MODIFY          
CONSTRUCTION OF THEIR POOLS.

NOTE: If a power drill is used during installation, it should be a variable speed 
drill used on low setting.  Torque should not exceed 58 inch pounds.  failure to 
comply could result in screws stripping out.

RIGID FRAMEWORK 

“SPLASHER”

SWIMMING POOL 

INSTRUCTIONS

D A N G E R

DO NOT DIVE OR JUMP INTO YOUR POOL!  ADULT SUPERVISION REQUIRED!

Your pool is approximately 4' deep. It is not designed for diving or jumping.  

If you dive or jump into your pool you run the risk 

of permanent injury or death.  Alert all visitors 

and family of this and point out all warning 

labels supplied. Watch children at all times. 

Pool not designed for diving or jumping!

KEEP A CLEAR SPACE 

OF AT LEAST 4 FEET 

AROUND THE POOL 

TO ELIMINATE 

THE POSSIBILITY 

OF CLIMBING 

INTO THE POOL

Summary of Contents for SPLASHER















Reviews: