background image

Adjustable height head installation

!

In addition to the guide below it is essential that the written instructions overleaf are read and 
understood and that you have all the necessary components (shown overleaf) before commencing
installation. Failure to install the product in accordance with these instructions may adversely affect
the warranty terms and conditions. Do not undertake any part of this installation unless you are 
competent to do so. Prior to starting ensure that you are familiar with the necessary plumbing 
regulations required to install the product correctly and safely.

Adjustable height heads are supplied with universal fixings.

The adjustable height heads are suitable to be fitted with either concealed or exposed shower valves. A wall 
outlet assembly is supplied for installation with a concealed valve. If fitting with an exposed valve please proceed
to instruction 7.

1

Prepare pipe work from the shower valve to the required position for the hose outlet
using a ø15mm copper pipe. Slide the 15mm gripper ring down the projecting pipe
up to the wall face. 

2

Trim the projecting pipe to a length of 15-22mm using a rotary type cutter.  If a hacksaw is used, the
pipe end must be carefully de-burred and chamfered.

3

Clean and lubricate the pipe using a suitable (silicone based) lubricant.

4

Remove the wall outlet cover plate and carefully slide the wall outlet onto the projecting pipe. Turn to 
the required position and mark the screw holes on the wall face. 

5

Remove the wall outlet and drill and prepare suitable wall fixings. Ensure the 
projecting pipe is clean and lubricate again if necessary. Refit the wall outlet and
secure it to the wall using the screws provided.

16

Colt installation guide:Dolphin install Guide  14/1/11  11:17  Page 16

Summary of Contents for Colt


























Reviews: