background image

General Safety   . . . . . . . . . . . . . . . . . . . . . . . .
Common Setups     . . . . . . . . . . . . . . . . . . . . . 
Placement    . . . . . . . . . . . . . . . . . . . . . . . .  
Unpacking / Installation    . . . . . . . . . . . . . . . 
Pivot / Utilities    . . . . . . . . . . . . . . . . . . . . . . .
Power Connection

  . . . .

 . . . . . . . . . . . . . . . . . 

Operation    . . . . . . . . . . . . . . . . . . . . . . . . . . 
Troubleshooting    . . . . . . . . . . . . . . . . . 
GT 500-HS Exploded View  . . . . . . . . . . 
Part Identification List   . . . . . . . . . . . . . . . . 
Oscillator Exploded View   . . . . . . . . . . . . . . 
Maintenance   . . . . . . . . . . . . . . . . . . . . . . . . 
Warranty    . . . . . . . . . . . . . . . . . . . . . . . . . . .

2

PAGE     

3

 4

 5 - 6

7
8
9

10

11 - 12
13 - 14

15
16

17

18

D

ESCRIPTION

Aquafog units are intended to condition large  

volumes of air using water or other non-hazardous 

liquids at air temperatures between 33ºF and 160ºF. 

Any other use of these units will void the warranty 

and the manufacturer will not be responsible for 
problems or damages resulting from misuse.

Safety Guidelines

This manual contains very important information. 

This information will help ensure SAFETY and 

PREVENT EQUIPMENT PROBLEMS. Use these 

symbols to understand safety guidelines.

DANGER

DANGER INDICATES AN 

IMMINENTLY HAZARDOUS

SITUATION WHICH, IF NOT AVOIDED, WILL RESULT IN 

DEATH OR SERIOUS INJURY.

WARNING INDICATES A 

POTENTIALLY HAZARDOUS

SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN 

DEATH OR SERIOUS INJURY.

CAUTION INDICATES A 

POTENTIALLY HAZARDOUS

SITUATION WHICH, IF NOT AVOIDED, MAY RESULT IN 

MINOR OR MODERATE INJURY.

NOTICE INDICATES IMPORTANT

INFORMATION, THAT IF NOT 

FOLLOWED, MAY CAUSE DAMAGE TO EQUIPMENT.

T

ABLE

 

OF

 C

ONTENTS

WARNING

CAUTION

NOTICE

Notes

www.JigglyGreenhouse.com  |  (800) 878-7829  |  [email protected]

Summary of Contents for GT 500-HS



















Reviews: