pH............................................................................................................................................................................................................2 pH - 11 pH
3
Maximum general hardness..............................................................................................................................................................400 ppm (mg / l)
Maximum alkaline...........................................................................................................................................................................................8 mval/l
3
Iron and manganese content........................................................................................................................................................
< 0.05 ppm
(mg / l)
1
The maximum SDI .............................................................................................................................................................................................SDI 5
2
3
The maximum salt content TDS ......................................................................................................................................................
2000 ppm
(mg / l)
1
SDI
-
(Silt Density Index) a coefficient which is of decisive importance in the process of the design of the reverse osmosis system. It expresses the
capability of water for contamination of membranes. Its value should amount to < 5.
2
TDS -
(Total Dissolved Solids) expressed the degree of salt content.
3
ppm
- ppm - one particle per million.
5. The parameters which are to be met by the water source water from which the water
is to be introduced into Reverse Osmosis (RO) systems*
6. Box contents
Water filtering system
EXCITO
-WAVE
Reverse Osmosis System
EXCITO
-OSSMO
Tank
PRO3200P*
7. The method of assembly of tubings to the JG (John Guest)
and QC (Quick connector) connecting sections
Disconnecting the tubing:
1) Take off the securing safety clip from the quick connector (fig. 1).
2) Press the flange of the quick connector in an even and symmetrical manner (fig. 2).
3) Pull the tubing out (fig. 3).
Connecting the tubing:
1) Press the tubing into the quick connector (the correctly assembled tubing is cartridgeed 1,5 cm deep into the quick connector) (fig. 4) .
2) Assemble the securing safety clip (fig. 5).
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
WARNING!
For the needs of the correct operation of the system what is indispensable is the installation of the pressure limiting device
PLV-0104-50
(3.3 bar - 50 psi). The device is responsible for the securing of the system against any sudden and rapid pressure changes as well as against the
occurrence of high pressure inside the system. The lack of the pressure regulating device results in the manufacturer's warranty becoming void.
Chrome faucet
FXFCH17-C
Tubing
KTPE14W
Shut-off
valve
Teflon tape
TAS0004
Connecting section
(1/2”
MIP
x 1/2”
MIP
x 1/4”
MIP
)
Ball valve for RO tank*
AQ-BV9014
Instructions
XI-EXCITO-TW
Installation Manual
Интсрукция монтажа
Instrukcja montażu
www.aquafilter.com
Wrench for
quick connectors
AQCWW-W
Drainage clamp
SC500B14*
* the element is included within the EXCITO-OSSMO system.
* distributor is not responsible for damages caused by the system operating with different inlet water parameters.
3
Summary of Contents for Clear Choice
