Aquacal Pool Pilot 75003 Owner'S Manual Download Page 23

Page: 23 / 55

INSTALLATION

Before Installing the #75001 Pool Pilot Pool Chemistry Controller System or
the #75004, #75005, #75006, or #75007 pH Acid Feed Pump and Tank System

•

Determine that everything needed for installation is on hand

•

Find a suitable mounting location for the Pool Chemistry Controller Unit within proper cord length to the Digital Control
Unit

•

Find a suitable mounting location for the Stenner acid feeder and tank.

•

Plan tubing runs for Flow Cell water sample tubing and Acid Feed lines

•

For optional #75008 pH Auxiliary Relay Kit, plan for electrical connections

What is included?

Before attempting the Total Control installation, check that the following items have been included with the Pool Chemistry
Controller:

Quantity Item

Description

#75001 Pool Chemistry Control unit with Flow cell, flow
switch, and interface cable

ORP sensor (in storage cap)

pH sensor (in storage cap)

Total Control interface cable

1 Mounting

Template

Plastic Mounting Wall Anchors

4 Mounting

Screws

16’ (5.3 m)

3/8” Water Sample tubing

Injection Fitting with gasket and S.S. saddle clamp

In-line check valve adapter fitting

Before attempting the pH Acid Feed Pump and Tank Kit installation, check that the following items have been included with the
pH Control System:

For #75008 Auxiliary Relay Kit

Quantity Item

Description

Auxiliary Relay box with internal relay and interface cable

Plastic Mounting Wall Anchors

4 Mounting

Screws

What is not included

Some of the additional equipment that is needed to complete the installation:

•

Drill with 3/8” bit

•

Utility Knife

For installations using Stenner Factory Tube and Fittings

•

¼” NPT drill and tap kit

•

Teflon Tape

For #75008 auxiliary relay kit

•

Appropriate gauge electrical wire

•

½”liquidtite (non-metallic flex) conduit

•

½” conduit connector for service to the Pool Pilot Digital Control unit

Quantity Item

Description

Stenner pH acid feed pump with 15 gallon acid tank

Injection Fitting with gasket and S.S. saddle clamp

In-line check valve adapter fitting

8’ (2.7 m)

1/8” ID x ¼” OD tubing

Cable Clamp and Nut assembly

1 pkg

Stenner Factory Parts Kit (fittings and components)

Summary of Contents for Pool Pilot 75003
























































Search results

Summary of Contents for Pool Pilot 75003

Reviews:

Related manuals for Pool Pilot 75003

Brands by name

Popular brands

Aquacal Pool Pilot 75003, Owner'S Manual

Search results

Summary of Contents for Pool Pilot 75003

Reviews:

Related manuals for Pool Pilot 75003

Brands by name

Popular brands