Aquacal AutoPilot PoolSync Owners And Installation Manual Download Page 6

Page: 6 / 16

Page - 3

CONTROL PANEL OVERVIEW

User Display

PoolSync

Label

Figure 1

Reset Button LED

Pressing this button will allow the PoolSync

to be reset.

Blinking

: Indicates the PoolSync

unit is Offline and not

connected to the network.

Fading

: Indicates the PoolSync

is connected to the local home

router.

Solid:

Indicates the PoolSync

is connected to the Cloud.

Service Mode Button LED

Indicates the unit is in Service Mode.

Blinking:

Indicates there may be a communication error.

Solid:

Indicates your system is being serviced and user control

is disabled.

Service Access and Setup Button LEDs

Fading:

This will allow a service technician to use the

PoolSync

as an access point when setting up all PoolSync

Ready equipment.

Solid:

Indicates the unit is in setup mode and ready to be

connected to the home network.

Summary of Contents for AutoPilot PoolSync

















Search results

Summary of Contents for AutoPilot PoolSync

Reviews:

Related manuals for AutoPilot PoolSync

Brands by name

Popular brands

Aquacal AutoPilot PoolSync, Owners And Installation Manual

Search results

Summary of Contents for AutoPilot PoolSync

Reviews:

Related manuals for AutoPilot PoolSync

Brands by name

Popular brands