background image

 

 

 

In case of replacement of cartridges or of the entire filter, follow the correct disposal 
rules provided by the state or region in which the product is installed.

 

 

In general, these rules prescribe: 
- CARTRIDGES: disposal as unsorted waste as it is dirty or soiled material; 
-  FILTERS  AND  VASES:  recycling  with  plastic  products  as  they  are  made  of 
polypropylene. However, any metal parts must first be removed. 
 

WARRANTY 

The product is guaranteed in accordance with the provisions of the AQUA SPA “General Conditions 
of Sale” document. 
The details of the guarantee provide that: 
- The item is used according to the instructions given by the manufacturer; 
- Installation and maintenance are carried out following the manufacturer's instructions; 
- The replacement under warranty is made only against the return of defective material, and after 
verifying the nature of the defect; 
-  The  warranty  is  intended  limited  to  the  replacement  of  the  part  recognized  as  defective,  and 
excludes any other right by the Purchaser to compensation for direct or indirect damage caused 
from the product itself. 
- The buyer agrees to pay all labor and transport costs necessary to replace the product covered by 
the warranty. 
- Failure to comply with the general rules indicated, as well as the neglect of the rules in force in 
Europe, will void any warranty on AQUA products. 
 
 
 

 

 
 
 
 
 
 
 
 
 

L0200681 - REV0 

Summary of Contents for FP2










Reviews: