background image

TROUBLESHOOTING

MOVES SLOWLY OR DOESN'T SEEM TO BE VACUUMING

• 

The solution is to make sure that the filter basket is clean.

• 

Check to see that the suction ports are not clogged or blocked.

ALL LED LIGHTS ARE BLINKING ON THE POWER SUPPLY

• 

Check to see if the unit is out of water.

• 

Check to see if the propeller is stuck.

• 

To restart, press the power button once. Cleaning program will resume from where it left off.

THE FLOATING CABLE IS COILED UP

• 

Change the axle set-up using the slider. Unit is most likely turning too sharply or in the same direction for too many cycles.

• 

Let the tangled cable lay flat in the sun; this will make it more pliable and easier to straighten.

• 

Never place more cable in the pool than it takes to get to the other side. (TIP: Mark the cable with black electric tape at correct length)

UNIT IS NOT SUCKING UP DEBRIS

• 

Check to see that you've properly set-up the unit and the power supply is ON.

• 

Check to see if the propeller is stuck.

• 

Adjust the suction ports on the bottom of the unit.

• 

Make sure the filter basket is clean.

UNIT IS STUCK IN THE MIDDLE OF THE POOL BUT THE UNIT STILL PUMPS OUT WATER

• 

Check to see that there is nothing obstructing the cleaner or that the cleaner is not stuck on any loose objects in the pool.

UNIT LOOKS LIKE IT IS MOVING IN THE SAME AREA OF THE POOL AND DOES NOT CLEAN OTHER AREAS

• 

Change the axle set up by adjusting the slider position. This will help move the cleaner in a different direction to clean.

• 

Always start your cleaner in the shallow end of your pool.

• 

Select the appropriate power supply setting be it Large or Small pool (certain models).

UNIT DOES NOT COVER THE ENTIRE POOL

• 

Check to see that the filter basket is thoroughly clean.

• 

Adjust the timing cycle on the power supply (certain models).

• 

Check to see that the axle and slider area is not blocked.

• 

Check and change your slider configuration.

For any additional questions 
or concerns please call

1-800-221-1750

280 Grove Avenue
Cedar Grove, NJ 07009
1-800-221-1750
www.aquaproducts.com

Summary of Contents for Aquabot









Reviews: