manualshive.com logo in svg

Aqua Lung SEA LV2, Technical Manual

Share
Download
Aqua Lung SEA LV2 Technical Manual Download Page 24

SEA MK / LV2 Technical Manual

24   

PART #

DESCRIPTION

APPLICATION

9-45171

Diagonal Pliers
Small

Removal / Installation of Clamp Strap (50)

053035

Valve Handle 
Retainer Tool

Removal / Installation of Pin Style Pressure Indicator (37)

100398

Insert, Tool 
Vise Jaws

Removal / Installation of First Stage Body (8) from Cylinder (43) 

(1.5 ft³ & 2 ft³ cylinders only)

(Not included in Tool Kit)

N/A

Torque
Wrench
 in-lbs

Apply torque to parts listed in 

Table 4: Torque Specifications

(Not included in Tool Kit)

N/A

Torque
Wrench
ft-lbs

Apply torque to parts listed in 

Table 4: Torque Specifications

(Not included in Tool Kit)

108343

108344

Service Kit, SEA First Stage
Service Kit, MK & LV2 Second Stage

Replacement Service Kit Parts

TABLE 3: LIST OF TOOLS AND SERVICE KITS (CONTINUED)

NOTE:  Photos of tools contained in the SEA tool kit are representative. Tool 

manufacturers and part numbers are subject to change without notice.

Summary of Contents for SEA LV2

































Reviews:

No comments

Brands by name

Popular brands

Load more brands