manualshive.com logo in svg

Aqua Lung SEA LV2, Technical Manual

Share
Download
Aqua Lung SEA LV2 Technical Manual Download Page 23

  23

TABLE 3: LIST OF TOOLS AND SERVICE KITS (CONTINUED)

PART #

DESCRIPTION

APPLICATION

9-BA819008

Magnifier
w/Illumination

Inspection of parts

820466

Christo-Lube 
MCG 111 2 oz.

Parts lubrication

947448

Screwdriver
Medium Blade
(Modified)

Removal / Installation of Handwheel Retainer (15)

54325A22

Strap 
Wrench

Removal / Installation of First Stage Body (8) from Cylinder (43)

103045

Flex Wrench 
3/8” Drive

Removal / Installation of parts

FC38A

9-43625

9-43628

1 3/16” Crowfoot
11/16” Crowfoot
7/8” Crowfoot

Removal / Installation of First Stage Body (8)
Removal / Installation of MP Hose (11)
Removal / Installation of Pressure Gauge (36)

9-43226

103006

9-43001

3/4” Socket
9/16” Socket
3/8” Socket

Removal / Installation of Bonnet (21) & Inlet Fitting (51)
Removal / Installation of Fill Port (33)
Removal / Installation of Safety Plug (9)

107394

Adjustable 
Spanner
Wrench

Removal / Installation of Retainer Cap (2)

9-44584

3/4” & 7/8"
Thin Wrench 

Hold Inlet Fitting (51) while tightening MP Hose (11)

9-AM11708

9-46661

1/8" Hex Bit Socket
3/16" Hex Bit Socket

Removal / Installation of Retainer (42)
Removal / Installation of Swivel Port Plug (14)

9-41971

1/4" Nut 
Driver

Removal / Installation of Locknut (62)

Summary of Contents for SEA LV2

































Reviews:

No comments

Brands by name

Popular brands

Load more brands