manualshive.com logo in svg

Aqua Lung G3000SS, Operation & Maintenance Manual

Share
Download
Aqua Lung G3000SS Operation & Maintenance Manual Download Page 72

APPENDIX K

CAMERA/LIGHT BRACKET (P/N 400107)

INSTALLATION INSTRUCTIONS 

This procedure is to be performed only by personnel who have received appropriate training. 

If you do not completely understand all of the procedure, contact Aqua Lung to speak directly 

with a Technical Advisor before proceeding any further.

Step 1: Remove two retainer port 

screws (11) from top corner of helmet 

using a Phillips #3 screwdriver.

Step 2: Line up bracket holes 

with helmet retainer holes.

Step 3: Replace the two retainer 

port screws (11) and tighten using 

a Phillips #3 screwdriver to 45 in.lbs 

(5 Nm).

Step 4: Right hand bracket installed.

Step 5: Left hand bracket installed.

Step-by-Step Assembly Instructions

Step 6: Left and Right brackets.

NOTE:

 

Brackets may 

be bent to shape as 

required.

72   

 Aqua Lung G3000SS Diving Helmet Operations & Maintenance Manual

Summary of Contents for G3000SS
























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands