manualshive.com logo in svg

Aqua Lung G3000SS, Operation & Maintenance Manual

Share
Download
Aqua Lung G3000SS Operation & Maintenance Manual Download Page 57

ANNUAL INSPECTION AND MAINTENANCE CHECKLIST (continued)

STEPS

PROCEDURE

INITIALS

FREE FLOW / WATER DUMP VALVE AND DEFOGGER

NOTE:

 

Refer to the free flow / water dump valve and defogger section of the 

Operations and Maintenance Manual for guidance.

FREE FLOW / WATER 

DUMP VALVE BODY

•  Remove the free flow / water dump valve from 

the helmet shell. Disassemble fully and visually 

inspect all parts for damage. Clean as required.

WATER DUMP EXHAUST 

FLAPPER VALVES

 

•  Visually inspect for cuts and damage. Wash with 

soap and water, rinse with fresh water and allow 

to dry. If necessary, replace water dump / exhaust 

flapper valve.

NOTE:

 

The flapper valves have a long 

service life and are not normally replaced 

annually.

O-RINGS (3)

•  Replace all o-rings (3) annually.

COPPER WASHERS (2)

•  Replace both copper washers annually.

VALVE SEAT

•  Visually inspect and check nylon seat condition. 
•  If necessary, replace entire free flow / water dump 

valve seat.

FREE FLOW / WATER 

DUMP VALVE STEM

•  Visually inspect for damage, bends and thread 

condition. 

•  If necessary, replace with new valve stem.

  57

Summary of Contents for G3000SS
























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands