AQmatic NX48 Service Manual Download Page 9

USER PROGRAMMING MODE FLOW 

CHART

Entering User Programming Mode

Hold the Up and Down buttons for 5 seconds.

FEED WATER

HARDNESS:

gpg

REGENERATION DAY
OVERRIDE: OFF

REGENERATION DAY
OVERRIDE:99 DAYS

REGENERATION
TIME:

02:00AM

Options:

 

U.S. Format 

[OFF] = default

Metric Format 

[OFF] = default

Options:

 

U.S. Format 

[gpg]

Metric Format 

[mgL]

Options:

 

U.S. Format 

[02:00AM] = default

Metric Format 

[02:00] = default

DIAGNOSTIC PROGRAMMING MODE 

FLOW CHART

Entering Diagnostic Programming Mode

1. Push and release the "D" button.
2. Press the Extra Cycle button once per display until all

displays are viewed and Normal Display is resumed.

3. Push and release the"D" button at anytime during

diagnostic mode and the timer will exit the mode.

4. Depending on the current controller programming, certain

displays may not be able to be viewed or set.

CURRENT FLOW

RATE:

0 gpm

PEAK FLOW RATE:

0 gpm

TOTALIZER:

130 g

LAST TWO REGENS:

0 HOURS

LAST REGEN

0 HOURS

VOLUME REMAIN:

1000 g

VALVE ADDRESS
#2

VERSION:

X.XX

Explaination:

 

Flow rate at this time.

Explaination:

 

Peak flow since last regeneration.

Explaination:

 

Gallons at the outlet since installation.

Explaination:

 

Hours between the last regeneration and the one before it.

Explaination:

 

Hours since last regeneration.

Explaination:

 

Volume remaining; can be adjusted.

Explaination:

 

Controller unit number.

Explaination:

 

Installed software level of the controller in use.

NXT Stager Controller     AU11 

Summary of Contents for NX48



















Reviews: