AQmatic NX48 Service Manual Download Page 7

REGEN TYPE:
TIME CLK DELAYED

Options:

 Time Clock Delayed (System 4 Only) 

(Default)

Meter Immediate (All System Types)

Meter Delayed Fixed Reserve (Systems 4 & 6 Only)

Example:

Time Clock Delayed 

(Default)

VALVE TYPE:
STAGER-NOTCH CAM

Options:

 2750 

2850

2900

3150

3900

Stager - Notch Cam  

(Default)

Example:

Stager - Notch Cam 

(Default)

REMOTE SIGNAL
START:OFF

Options:

 00:06:00 (Hours:Munutes:Seconds)

Range: 

1 second to 99 minutes (1 hour, 39 minutes)

Example:

Off 

(Default)

DISPLAY FORMAT:
US-GALLONS

Options:

 U.S. - Gallons 

(Default)

EU-Metric - Liters (Metric)

Example:

U.S. Gallons 

(Default)

UNIT CAPACITY:
 0300000  GRAINS

Options:

 Grains (in U.S. Format) 

(Default)

Grams (in Metric Format)

Example:

0300000 Grains 

(Default)

CAPACITY SAFETY
FACTOR:

00%

Range: 

0 to 50%

Example:

00% 

(Default)

FEED WATER
HARDNESS: 15 GPG

Range: 

1 to 199 Grains/Gallon (U.S. Format)

2 to 199 miligrams CaCO

s

/L (Metric Format)

Example:

15 GPG (U.S. Format) 

(Default)

TRIP POINT 1:

 000 gpm

Range:

 2 to 4 Valves in the System

NOTE: This screen will not display for System Type 4.

NOTE: In European Units - Liters (Metric) mode, the display will be in 

24-hour time.

NOTE: In U.S. - Gallons mode, the display will be in 12-hour time.

NOTE: Use the Shift button to move to the left.

Range: 

1 to 9,900,000 Grain Capacity in U.S. Format

1.0 to 190,000 grams CaCO

3

 Capacity in Metric Format

NOTE: Use the Shift button to move to the left.

NOTE: Use the Shift button to move to the left.
NOTE: This screen will only display on the lead unit for System Types 6 & 7.

For all other System Types, it will display for all units.

NOTE: Display will only appear on the master timer and it must be 

programmed as valve position #1. Use the Shift button to change each 

decimal position.

NOTE: This screen will only display for System 14.

TRIP POINT 2:

gpm

NOTE: This display will not be viewed in System 14.

NOTE: Display will only appear on the master timer and it must be 

programmed as valve position #1. Use the Shift button to move one space 

to the left.

TRIP DELAY 1:

30 SECONDS

NOTE: This screen will only display for System 14.

1 to 997 gpm

1 to 3997 Lpm

2 to 998 gpm

VALVE ADDRESS:

#2

Options:

 Valve Address #1 (First Control Valve)

Valve Address #2 (Second Control Valve) 

(Default)

Valve Address #3 (Third Control Valve)

Valve Address #4 (Fourth Control Valve)

 

SYSTEM TYPE:

4

  SINGLE UNIT

Options:

 System 4 (single unit)

System 5 (2-4 units) - Parallel Interlock

System 6 (2-4 units) - Parallel Series Regeneration

System 7 (2 units) - Alternating

System 9 (2-4 units) - Alternating

System 14 (2-4 units) - Demand Recall

Example:

System Type 4, Single Unit

Example:

Valve Address #2 (Second Control Valve) 

(Default)

SYSTEM SIZE:

2 VALVES

Options:

 2 Valves in the System 

(Default)

3 Valves in the System

4 Valves in the System

Example:

2 Valves in the System 

(Default)

REGEN TYPE:
TIME CLK DELAYED

Example:

Time Clock Delayed 

(Default)

SELECT LANGUAGE:
  ENGLISH

Options:

 English

Espanol

Portugues

Deutsch

Francais

Example:

English

Range:

 2 to 4 Valves in the System

NOTE: This screen will not display for System Type 4.

NOTE: This screen will not display for System Type 4.

MASTER PROGRAMMING MODE FLOW 

CHART

CAUTION

 Before entering Master Programming, please 

contact your local professional water dealer.

When the Master Programming Mode is entered, parameters 

can be set to make the timer(s) function as needed. 

NOTE: Depending on current option settings, some 

displays cannot be viewed or set. 

Entering Master Programming Mode

1. Press and hold the Shift and Up buttons for 5 seconds.

OR

2. Set the time of day display to 12:01 PM or 12:01HR. Press

and hold Up or Down buttons to set the time. Then press

the Up and Down buttons at the same time for 5 seconds.

Exiting Master Programming Mode

1. Press the Extra Cycle button once per display until all

are viewed. Master Programming Mode is exited and the

normal display screen appears.

2. To exit the Master Programming Mode without saving

changes, press the Diagnostic button.

NOTE: If no keypad activity is made for 5 minutes while 

in the Master Programming Mode, or if there is a 

power failure, no changes will be saved, and the 

unit will go back to the main display screen.

Resets

Soft Reset: 

Press and hold the Up and Down buttons for 25 

seconds until 12:00PM (or 12:00HR) appears. This resets all 

parameters except for the 

 meter totalizer volume.

Master Reset: 

Hold the Extra Cycle button while powering up 

the unit. This resets all of the parameters in the unit. Check 

and verify the choices selected in Master Programming Mode.

NXT Stager Controller 

AU11 

Summary of Contents for NX48



















Reviews: