manualshive.com logo in svg

APS REG-12S-100, Instruction Manual

Share
Download
APS REG-12S-100 Instruction Manual Download Page 16

M982282AP-03-13A                                                                                   

REG-6S-100

 / 

REG-12S-100

 

 

- 16 - 

7 

RUN STATUS 

Once  the  device  has  been  configured  according  to  installation  needs  it  can  be  set  to  RUN  mode  to 
regulate  the  PF  of the  installation.  RUN mode is  the  default mode  after exiting the set-up menu or after 
the device start (supply connection followed by a short initialisation period).  When the device is in RUN 
mode it can reach one of the following status: 

a)  Normal  RUN  status  (Absence  of  alarm):

  In  this  status  the  device  performs  the  automatic  PF 

regulation, connecting and disconnecting the capacitor stages according to installation needs. In 
this  status  the  user  can  access  to  the  measurement  of  different  parameters  and  can  also  force 
the manual connection or disconnection of capacitor stages as described in paragraph 7.1.  

b)  Alarm  status: 

If  any  of  the  anomalous  situations  described  in  paragraph  3.2  occur,  the  device 

jumps to alarm status and displays the error code. Depending on the error type the regulator may 
perform the disconnection of all the stages or continue regulating the PF as in normal RUN. 

 

7.1 

Functions of the device in normal RUN mode. 

In the normal RUN mode the REG-6S-100 and REG-12S-100

 

can perform the following functions: 

 

long

 

Manual connection of capacitor stages. 

Keep the key pushed during more than 1s 

and  the regulator will sequentially connect the different steps, following the normal 
program and respecting the delay time 

t

on

 set in the set-up procedure

 

 long

 

Manual disconnection of capacitor stages: 

Keep the key pushed during more than 

1s and  the regulator will sequentially disconnect the different steps, following the 
normal program and respecting the delay time 

t

off

 set in the set-up procedure. 

 

 

Displaying the number of connected steps: 

If both keys are simultaneously pushed 

the device displays the Nr of connected steps. (Remember the difference between step 
and stage described in paragraph 1.1) 

 

short

 

Parameters measurement:  

Performing successive short pushing of this key (<1 s), 

the user can travel along several display screens showing the values of the following 
parameters:  (cos) , cosinus 

 of the installation ; (I) , mains current; (THD), THD of 

mains current; (V) , Mains voltage; (I, MAX), Maximum value of mains current since the 
last clear; (V MAX), Maximum value of mains voltage since the last clear. The 
displayed parameter is pointed by the cursor   

 short

 

Parameters measurement:  

Performing successive short pushing of this key (<1 s), 

the user can travel through the readings of the same parameters described above but 
in reverse order.  

 

long

 

Start the SET-UP mode

: 

:  

Performing a long push of this key (<1 s), the device jumps 

to set-up mode. 

  

 MAX 

Clear MAX values

: Performing a long push of this key (<1 s) while the cursor   is 

pointing to MAX , REG-6S-100 and REG-12S-100 clears the maximum values of 
voltage and current recorded since the last clear. 

Summary of Contents for REG-12S-100


















Reviews:

No comments

Brands by name

Popular brands

Load more brands