APS 3A Series Operation Manual Download

Page: 29 / 56

3A SERIES

OPERATION MANUAL

Entire Contents Copyright



3A SERIES AC & DC LOAD OPERATION MANUAL

Page 29 of 56

Key # Description

FREQ key and annunciator

The function of this key depends on the selected operating mode as follows:

CC mode

After pressing the FREQ key, the annunciator will turn on. Parameters are

selected in the following order by repeatedly pressing the FREQ key:

FREQ



BANK (except in DC mode)



SYNC



Off

Available AC parameter setting ranges are:

FREQ DC, 0.1 to 400 Hz.

BANK 0 through 10 for 11 banks total

SYNC ON = External Sync, OFF = Internal Sync

LIN & CR modes

After pressing the FREQ key, the annunciator will turn on. Pressing the

FREQ key again will turn it off.

AC or DC Load Input Connections

Before connecting any source or supply to the 3A load module banana jack connectors, make

sure that the rated specification of the voltage and current of the 3A Series model will not be

exceeded. Before wiring the load input, please refer to Section 7.1, “

INPUT Terminals

” to avoid

damaging the internal circuits and connectors.

V Sense Connector

Refer to Section 7.4, on “

Voltage Sense Input Terminals

” for information on external voltage

sense connections.

I-Monitor Output BNC

Refer to Section 7.5, on “

Current Output Monitor (I-Monitor)

” for further information on

using this feature.

Table 6-1: Front Panel Display and Keyboard Functions

Summary of Contents for 3A Series

























































Search results

Summary of Contents for 3A Series

Reviews:

Related manuals for 3A Series

Brands by name

Popular brands

APS 3A Series, Operation Manual

Search results

Summary of Contents for 3A Series

Reviews:

Related manuals for 3A Series

Brands by name

Popular brands