manualshive.com logo in svg

APS 3A Series, Operation Manual

Share
Download
APS 3A Series Operation Manual Download Page 22

 

 

3A SERIES

 

OPERATION MANUAL 

 

 

 

Entire Contents Copyright 

 2014 by Adaptive Power Systems, Inc. (APS) • All Rights Reserved • No reproduction without written authorization from APS. 

3A SERIES AC & DC LOAD OPERATION MANUAL 

Page 22 of 56 

 

Procedure for installation of 3A Series load modules: 

1.

 

Prior to installation of a load module, please 

TURN OFF

 

the power switch of the 

mainframe. 

Failure to do so could damage a load module.

 (No hot-swap capability). 

2.

 

Align the upper and lower guide-slot of the module position inside the mainframe into 

which the module is to be installed and carefully insert the load in that slot position. 

3.

 

As shown in Figure 5-1, push the load module into the mainframe by pressing against 

the two load input terminals on the front panel until the module is fully seated. 

4.

 

Tighten the locking screw located at lower right side of the front panel.   

NOTE:

 

Do NOT over-tighten this screw

. It does not need to support the weight of the 

module, just prevent it from pulling out when removing cables from the front panel. 

5.

 

Turn on the power of the mainframe only 

after

 all load modules are securely installed. 

 
Procedure for removal of 3A Series load modules: 

To REMOVE a module, reverse steps 4 through 3 in the installation procedure above. 

5.3

 

Cleaning 

To clean this product uses a soft or slightly damp cloth. 

 

CAUTION 

 

 

BEFORE you clean the unit, switch the mains power off and disconnect the 
input line cord. 

・

Please do NOT use any organic solvent capable of changing the nature of 

the plastic such as benzene or acetone. 

・

Please ensure that no liquid is allowed to penetrate this product. 

 

 

5.4

 

Powering Up 

Refer to the 34M01 Mainframe Operation Manual (P/N 160921) or 34M04 mainframe 

Operation Manual (P/N 160924). 

5.5

 

In Case of Malfunction 

In the unlikely event of an instrument malfunction or if the load module does not function, 

please attach a warning tag to the instrument to identify the owner and indicate that service or 

repair is required. Contact Adaptive Power Systems or its authorized representative to arrange 

for service. 

Summary of Contents for 3A Series

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands