APS 3A Series Operation Manual Download Page 40 | Manualshive

Page: 40 / 56

background image

3A SERIES

OPERATION MANUAL

Entire Contents Copyright



2014 by Adaptive Power Systems, Inc. (APS) • All Rights Reserved • No reproduction without written authorization from APS.

3A SERIES AC & DC LOAD OPERATION MANUAL

Page 40 of 56

6.3.4

Last Setting Recall

All 3A Series load modules provide a ‘last setup recall’ feature. Using this feature, any 3A load

module can be set to return to the last setup state in effect at power off. This occurs the next

time the load is turned back on and immediately following its power-on self-test. So rather than

returning to the factory default setting shown in the tables above, it will return to the last state

in which it was used.

6.3.5

Setup Memory Reset

If for any reason the non-volatile setup memory has been corrupted, it can be cleared and

returned to factory defaults

(RESET)

using by pressing the “SENSE” and “PRES” keys on the front

panel of the load module simultaneously.
During this RESET procedure, the display will show the load model number and firmware

revision repeatedly and reset all settings to the factory defaults shown in the tables above until

the keys are released.

«
...
38
39
40
41
42
...
»

Summary of Contents for 3A Series

























































Reviews:

No comments

Related manuals for 3A Series

Brand: Kawai Pages: 70

Brand: Bartington Pages: 15

Brand: Bartec Pages: 216

Brand: YOKOGAWA Pages: 2

Brand: VEE GEE Pages: 2

Brand: PAT Pages: 57

Brand: ISKRAEMECO Pages: 12

RAVTD1760WS Series

Brand: Ravaglioli Pages: 24

Brand: PCE Health and Fitness Pages: 11

Brand: Wacom Pages: 23

Brand: IFM Pages: 13

Brand: BART Pages: 24

Brand: Vega Pages: 36

Brand: Hanna Instruments Pages: 2

Brand: Ocean Reef Pages: 20

Brand: E+E Elektronik Pages: 3

Celviano GP-300

Brand: Casio Pages: 78

Brand: IET Labs Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands