Applied Precision RS 1130 User Manual Download Page 16 | Manualshive

Page: 16 / 59

background image

Reference Standard RS 2x30, RS 1x30

User’s Guide

RS-UG91-EN

www.appliedp.com

16

3.2.14 RS-232 Menu

Baud Rate

- parameter setting the RS-232 serial line communication rate set value in bauds.
The value of the parameter is 4800, 9600, 19200, 38400, 57600 or 115200
bauds, respectively,

Data bits

- parameter setting the number of data bits set value on the RS-232 serial line.
The parameter value is 7 or 8, respectively,

Parity

- parameter setting the RS-232 serial line set value. The parameter value is
“ODD” for the odd parity, EVEN for the even parity and NO for the no parity,
respectively,

Stop bits

- parameter setting the number of stop bits set value on the RS-232 serial line.
The parameter value is 1 or 2, respectively,

3.2.15 Display Menu

Quantities...

- quantities menu

Display

- parameter setting the state of measured results values appeared on the display.
The value of the parameter is ON or OFF for the switched-on or switched-off
results depicting on the display, respectively. Parameter is not related to the
device menu depicting, which is displayed always if it is activated,

Resolution

- resolution setting: STANDARD = results with standard number of decimal digits
according to the shown variable type; HIGH

– number of decimal digits is raised

by 1 comparing to option STANDARD; MAXIMAL - number of decimal digits is
raised by 2 comparing to option STANDARD.

Service Info

- enabling or disabling (ON / OFF) of service information

Large Font

- parameter setting the state when measured quantity is displayed in large font.
The option is activated if only one quantity is chosen to be displayed,

Harm. Graph...

- harmonic items graph menu

Contrast...

- display contrast change menu

VGA Output

- parameter Disables or Enables VGA output on the rear side of newer devices

3.2.16 Keyboard Menu

Beep

- enabling or disabling the beep functionality of the keyboard,

Lock@SwitchOn

- enabling or disabling the automatic keypad lock right after each device switch

on

Lock Password

- keypad unlocking password change

Lock Now ->

- instant keypad lock with a basic mode activation.

3.2.17 Impulse Menu

FoutX Config. ...

- four similar items (where X = 0,1,2,3) for four impulse outputs of the device.
Each one represents an access into submenu containing settings of particular
impulse output.

Fin Meas/Test ...

- Frequency Input menu

OPS Meas/Test ...

- OPS Measurement Mode menu

«
...
14
15
16
17
18
...
»

Summary of Contents for RS 1130




























































Reviews:

No comments

Related manuals for RS 1130

Workstation Monitor 724

Brand: 3M Pages: 21

Brand: 3M Pages: 2

Brand: 3M Pages: 2

Brand: 3M Pages: 24

Brand: 3M Pages: 2

SoundPro SE Series

Brand: 3M Pages: 293

Brand: Keithley Pages: 48

Brand: Kane Pages: 16

Brand: Bacharach Pages: 48

Brand: Bacharach Pages: 24

Brand: Macnaught Pages: 14

Brand: Raytech Pages: 18

Brand: PASCO Pages: 3

Brand: Solinst Pages: 2

350 Maritime V2

Brand: TESTO Pages: 106

Solar Auxiliary Power Unit

Brand: J-TECH Pages: 6

Brand: Lumel Pages: 32

Brand: horiba Pages: 103

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands