background image

-10-

Connecting to the PC

Locate your computer within 6 feet of the Si5580.

Your Si5580 was shipped with a black adapter plug.  It has a telephone style jack at one end and a 

larger 9 pin connector at the other.  Plug the large end into the COM1 serial port of your PC.  Secure 

the adapter with the screws on the sides.  If the COM1 port on your PC is already used by something 

else, you may use the COM2 port for the Si5580.  On some PCs, COM2 will have a 25 pin connector 

that does not fit the black adapter plug.  If this is the case, and you must use COM2, you may have to 

purchase a 25 to 9 pin serial adapter at your local computer store.

Your Si5580 was also shipped with a 7 foot telephone line cord.  Plug one end into the adapter we 

just attached to your PC, and the other end into the PC/MMI jack on your Si5580.

Never connect the Si5580 to a telephone circuit.  It uses the same connec-

tors and cords as telephones and modems, but the voltages are not compat-

ible.

Programming Note:  Always apply power to the Si5580 after the Si Programmer

TM

 software is running 

on your PC.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for Si5580



























Reviews: