manualshive.com logo in svg

Applied Instruments XR-3, Operation Manual

Share
Download
Applied Instruments XR-3 Operation Manual Download Page 66

XR-3 TS2 Module Operation Manual 

 

XR-3 

 

Page 66 of 66 

 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Applied Instruments, Inc. 

5230 Elmwood Avenue 

Indianapolis, IN 46203 USA 

http://www.appliedin.com

 

 

 

Tel: +1 (317) 782-4331 

Toll-free USA Tel: (800) 244-2976 

Fax: +1 (317) 786-9665 

Email: 

[email protected]

 

 

 

 

WARRANTY 

 

The Applied Instruments XR-3 is warranted against defects in materials and workmanship for a period 
of twelve months.  Applied Instruments agrees to repair or replace any assembly or component found 
to be defective under normal use during this period.  Our obligation under this warranty is limited 
solely to repairing the instrument proven to be defective within the scope of the warranty when 
returned to the factory.  Transportation to the factory is to be prepaid by the customer.  Authorization 
(RMA#) by Applied Instruments is required prior to shipment. 
 
Applied Instruments assumes no liability for secondary charges or consequential damages and, in any 
event, Applied Instruments’ liability for breach of warranty under any contract shall not exceed the 
purchase price of the instrument shipped, and against which a claim is made. 
 
Any application recommendation made by Applied Instruments for the use of its products is based 
upon tests believed to be reliable, but Applied Instruments makes no guarantee of the results to be 
obtained.  This warranty is in lieu of all other warranties, expressed or implied, and no representative 
or person is authorized to represent or assume for Applied Instruments any liability in connection with 
the sale of our products other than that set forth herein. 

 

TESCOM USA

TESCOMUSA.COM

Summary of Contents for XR-3



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands